ADF4216 Datasheet PDF - Analog Devices
| Part Number | ADF4216 | |
| Description | Dual RF PLL Frequency Synthesizers | |
| Manufacturers | Analog Devices | |
| Logo |  |
|
|
There is a preview and ADF4216 download ( pdf file ) link at the bottom of this page. Total 20 Pages | ||
Preview 1 page No Preview Available !
a
Dual RF PLL Frequency Synthesizers
ADF4216/ADF4217/ADF4218
FEATURES
GENERAL DESCRIPTION
ADF4216: 550 MHz/1.2 GHz
The ADF4216/ADF4217/ADF4218 are dual frequency synthe-
ADF4217: 550 MHz/2.0 GHz
sizers that can be used to implement local oscillators (LOs) in
ADF4218: 550 MHz/2.5 GHz
the upconversion and downconversion sections of wireless
2.7 V to 5.5 V Power Supply
receivers and transmitters. They can provide the LO for both
Selectable Charge Pump Currents
the RF and IF sections. They consist of a low-noise digital PFD
Selectable Dual Modulus Prescaler
(Phase Frequency Detector), a precision charge pump, a pro-
IF: 8/9 or 16/17
RF: 32/33 or 64/65
3-Wire Serial Interface
Power-Down Mode
APPLICATIONS
Wireless Handsets (GSM, PCS, DCS, CDMA, WCDMA)
OBase Stations for Wireless Radio (GSM, PCS, DCS,
CDMA, WCDMA)
BWireless LANS
Communications Test Equipment
SOCATV Equipment
grammable reference divider, programmable A and B counters,
and a dual-modulus prescaler (P/P+1). The A (6-bit) and B
(11-bit) counters, in conjunction with the dual modulus prescaler
(P/P+1), implement an N divider (N = BP + A). In addition,
the 14-bit reference counter (R Counter), allows selectable
REFIN frequencies at the PFD input. A complete PLL (Phase-
Locked Loop) can be implemented if the synthesizers are
used with an external loop filter and VCOs (Voltage Con-
trolled Oscillators).
Control of all the on-chip registers is via a simple 3-wire interface.
The devices operate with a power supply ranging from 2.7 V
to 5.5 V and can be powered down when not in use.
LFUNCTIONAL BLOCK DIAGRAM
EVDD1 VDD2 VP1 VP2
TEN=BP+A
ADF4216/ADF4217/ADF4218
IFINA
IFINB
IF
PRESCALER
11-BIT IF
B-COUNTER
PHASE
COMPARATOR
CHARGE
PUMP
CPIF
6-BIT IF
A-COUNTER
IF
LOCK
DETECT
REFIN
CLOCK
DATA
LE
OSCILLATOR
22-BIT
DATA
REGISTER
SDOUT
RFINA
RFINB
N = BP + A
RF
PRESCALER
14-BIT IF
R-COUNTER
14-BIT IF
R-COUNTER
11-BIT RF
B-COUNTER
6-BIT RF
A-COUNTER
OUTPUT
MUX
MUXOUT
RF
LOCK
DETECT
PHASE
COMPARATOR
CHARGE
PUMP
CPRF
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
DGNDRF AGNDRF DGNDIF DGNDIF AGNDIF
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700 World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2000
|
| |
 
ADF4216/ADF4217/ADF4218
PIN FUNCTION DESCRIPTIONS
Pin No. Mnemonic Function
1 VDD1 Positive Power Supply for the RF Section. Decoupling capacitors to the analog ground plane should be
placed as close as possible to this pin. VDD1 should have a value of between 2.7 V and 5.5 V. VDD1 must
have the same potential as VDD2.
2 VP1
Power Supply for the RF Charge Pump. This should be greater than or equal to VDD.
3 CPRF
Output from the RF Charge Pump. When enabled this provides ± ICP to the external loop filter, which in
turn drives the external VCO.
4 DGNDRF Ground Pin for the RF Digital Circuitry.
5
RFINA
Input to the RF Prescaler. This low-level input signal is normally ac-coupled to the external VCO.
6
RFINB
Complementary Input to the RF Prescaler. This point should be decoupled to the ground plane with a small
bypass capacitor, typically 100 pF.
7 AGNDRF Ground Pin for the RF Analog Circuitry.
8
REFIN
Reference Input. This is a CMOS input with a nominal threshold of VDD/2 and an equivalent input resis-
tance of 100 kΩ. This input can be driven from a TTL or CMOS crystal oscillator or it can be ac-coupled.
9 DGNDIF Ground Pin for the IF Digital (Interface and Control Circuitry).
10 MUXOUT This multiplexer output allows either the IF/RF lock detect, the scaled RF, or the scaled Reference Fre-
O quency to be accessed externally. See Table V.
B11 CLK
Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is latched
into the 22-bit shift register on the CLK rising edge. This input is a high impedance CMOS input.
S12 DATA Serial Data Input. The serial data is loaded MSB first with the two LSBs being the control bits. This input is
Oa high impedance CMOS input.
L13 LE
Load Enable, CMOS Input. When LE goes high, the data stored in the shift registers is loaded into one of
the four latches, the latch being selected using the control bits.
E14 AGNDIF Ground Pin for the IF Analog Circuitry.
TE15 IFINB
Complementary Input to the IF Prescaler. This point should be decoupled to the ground plane with a small
bypass capacitor, typically 100 pF.
16 IFINA
Input to the IF Prescaler. This low-level input signal is normally ac-coupled to the external VCO.
17 DGNDIF Ground Pin for the IF Digital, Interface, and Control Circuitry.
18 CPIF
Output from the IF Charge Pump. When enabled this provides ± ICP to the external loop filter, which in turn
drives the external VCO.
19 VP2
Power Supply for the IF Charge Pump. This should be greater than or equal to VDD.
20 VDD2
Positive Power Supply for the IF, Interface, and Oscillator Sections. Decoupling capacitors to the analog
ground plane should be placed as close as possible to this pin. VDD2 should have a value of between 2.7 V
and 5.5 V. VDD2 must have the same potential as VDD1.
PIN CONFIGURATION
VDD1 1
20 VDD2
VP1 2
19 VP2
CPRF 3
18 CPIF
DGNDRF 4 TSSOP 17 DGNDIF
RFINA 5 ADF4216/ 16 IFINA
RFINB 6 ADF4217/ 15 IFINB
AGNDRF 7 ADF4218 14 AGNDIF
REFIN 8
13 LE
DGNDIF 9
12 DATA
MUXOUT 10
11 CLK
REV. 0
–5–
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for ADF4216 electronic component. |
| Information | Total 20 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ ADF4216.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| ADF4210 | The function is Dual RF/IF PLL Frequency Synthesizers. Analog Devices | |
| ADF4211 | The function is Dual RF/IF PLL Frequency Synthesizers. Analog Devices | |
| ADF4212 | The function is Dual RF/IF PLL Frequency Synthesizers. Analog Devices | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
ADF4
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||