DataSheetWiki


HCPL-0500 fiches techniques PDF

AVAGO - High Speed Optocouplers

Numéro de référence HCPL-0500
Description High Speed Optocouplers
Fabricant AVAGO 
Logo AVAGO 





1 Page

No Preview Available !





HCPL-0500 fiche technique
6N135/6, HCNW135/6
HCPL-2502/0500/0501
Single Channel, High Speed Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
These diode-transistor optoc­oup­lers use an insulating
layer between a LED and an integrated photodetector to
provide elec­trical ins­u­lation between input and out­put.
Separate connections for the photodiode bias and out-
put-transistor collector increase the speed up to a hun-
dred times that of a conven­tional phototransistor coupler
by reduci­ng the base-collector capacitance.
These single channel optocoupl­ers are available in
8-Pin DIP­, SO-8 and Widebody package configurations.
The 6N135, HCPL-0500, and HCNW135 are for use in TTL/
CMOS, TTL/LSTTL or wide bandwidth analog applications.
Current transfer ratio (CTR) for these devices is 7% mini-
mum at IF = 16 mA.
The 6N136, HCPL-2502, HCPL-0501, and HCNW136 are
designed for high speed TTL/TTL applications. A standard
16 mA TTL sink current through the input LED will pro-
vide enough output current for 1 TTL load and a 5.6 k
pull-up resistor. CTR for these devices is 19% minimum at
IF = 16 mA.
Functional Diagram
NC 1
ANODE 2
CATHODE 3
NC 4
8 VCC
7 VB
6 VO
5 GND
TRUTH TABLE
(POSITIVE LOGIC)
LED VO
ON LOW
OFF HIGH
Features
High speed: 1 Mb/s
TTL compatible
Available in 8-Pin DIP, SO-8, widebody packages
Open collector output
Safety approval
UL
for
Recognized – 3750
1 minute for HCNW
Varnmds fOorp1tiomnin0u2t0ed(5e0v0ic0eVs)rms
per UL1577
CSA Approved
IEC/EN/DIN EN 60747-5-5 Approved
–––deVVVvIIIOOOiRRRcMMMes===
567 V peak for SO-8 devices
630 V peak for DIP 300 mil devices
1414 V peak for DIP 400 mil (widebody)
Dual channel version available (253X/053X/0534)
Applications
High voltage insulation
Video signal isolation
Line receivers
Feedback element in switched mode power supplies
High speed logic ground isolation
– TTL/TTL, TTL/CMOS, TTL/LSTTL
Replaces pulse transformers
Replaces slow phototransistor isolators
Analog signal ground isolation
A 0.1 µF bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.

PagesPages 16
Télécharger [ HCPL-0500 ]


Fiche technique recommandé

No Description détaillée Fabricant
HCPL-0500 SINGLE CHANNEL HIGH SPEED TRANSISTOR OPTOCOUPLERS Fairchild Semiconductor
Fairchild Semiconductor
HCPL-0500 Single Channel/ High Speed Optocouplers Agilent(Hewlett-Packard)
Agilent(Hewlett-Packard)
HCPL-0500 (HCPL-xxxx) Single Channel / High Speed Optocouplers Hewlett-Packard
Hewlett-Packard
HCPL-0500 High Speed Optocouplers AVAGO
AVAGO

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche