DataSheetWiki


HMC862LP3E fiches techniques PDF

Hittite Microwave - LOW NOISE PROGRAMMABLE DIVIDER

Numéro de référence HMC862LP3E
Description LOW NOISE PROGRAMMABLE DIVIDER
Fabricant Hittite Microwave 
Logo Hittite Microwave 





1 Page

No Preview Available !





HMC862LP3E fiche technique
HMC862LP3E
v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
Typical Applications
4 The HMC862LP3E is ideal for:
• Satellite Communication Systems
• Point-to-Point & Point-to-Multi-Point Radios
• Military Applications
• Test Equipment
Functional Diagram
Features
Low Noise Floor: -153 dBc/Hz at 100 kHz offset
Programmable Frequency Divider, N = 1, 2, 4, 8
Wide Bandwidth: 100 MHz to 15 GHz
16 Lead 3X3 mm SMT Package: 9mm2
General Description
The HMC862LP3E is a low noise programmable
frequency divider in a 3x3 mm leadless surface
mount package. The divider can be programmed
to divide from N=1, 2, 4, 8 in the 100 MHz to
15 GHz input frequency range. The low phase
noise, wide frequency range and flexible division
ratio make this device ideal for high performance and
wide band communication systems.
4-1
Electrical Specifications, TA = +25° C, Vcc1 = Vcc2 = +5V
Parameter
Conditions
Min. Typ. Max.
Units
RF Input Characteristics
Max RF Input Frequency
Min RF Input Frequency
RF Input Power Range (N = 1)
RF Input Power Range (N = 2, 4, 8)
Divider Output Characteristics
Output Power (N = 1)
Sine Wave or Square Wave Input
Sine Wave or Square Wave Input [1]
Sine Wave or Square Wave Input [1] [2] Fin < 8 GHz
Sine Wave or Square Wave Input [1] [2] Fin > 8 GHz
Sine Wave or Square Wave Input [1]
(see the Pout plot for N = 1) [2]
15
0.1
-10 10
-10 0
-10 10
-2 to +3
GHz
GHz
dBm
dBm
dBm
dBm
Output Power (N = 2, 4, 8)
(see the Pout plots for each division ratio)
2 dBm
Divider Ratio N
1, 2, 4, 8
SSB Phase Noise @ 100 kHz Offset
Fin = 6 GHz, Pin = 0 dBm, N = 2
-153
dBc/Hz
Logic Inputs
VIH Input High Voltage
3 5V
VIL Input Low Voltage
Power Supplies
0 0.4 V
Vcc
Analog Supply
4.75 5 5.25
V
Current Consumption
N = 1, S0 = L, S1 = L, S2 = L
106 mA
Icc
N = 2, S0 = H, S1 = L, S2 = L
N = 4, S0 = H, S1 = H, S2 = L
143 mA
153 mA
N = 8, S0 = H, S1 = H, S2 = H
162 mA
Control Bits
3 Bit
[1] Square wave input waveform is recommended below 400 MHz for best phase noise performance. If sine wave input waveform is used below
400 MHz, it is recommended that power input is > +5 dBm for best operation including phase noise performance.
[2] For N = 1, frequencies > 8 GHz, and input power > 0 dBm, output power will saturate and gradually drop with increasing input power, but
part will continue to function.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]

PagesPages 10
Télécharger [ HMC862LP3E ]


Fiche technique recommandé

No Description détaillée Fabricant
HMC862LP3E LOW NOISE PROGRAMMABLE DIVIDER Hittite Microwave
Hittite Microwave

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche