TSOP32230 Datasheet PDF - Vishay
| Part Number | TSOP32230 | |
| Description | IR Receiver Modules | |
| Manufacturers | Vishay | |
| Logo |  |
|
|
There is a preview and TSOP32230 download ( pdf file ) link at the bottom of this page. Total 10 Pages | ||
Preview 1 page No Preview Available !
TSOP322.., TSOP324.., TSOP344.., TSOP348..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
1
2
3
MECHNICAL DATA
Pinning for TSOP348.., TSOP344..:
1 = OUT, 2 = GND, 3 = VS
Pinning for TSOP322.., TSOP324..:
1 = OUT, 2 = VS, 3 = GND
16672
FEATURES
• Very low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage: 2.5 V to 5.5 V
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
DESCRIPTION
The TSOP322.., TSOP348.., TSOP324.. and TSOP344..
series are miniaturized IR receiver modules for infrared
remote control systems. A PIN diode and a preamplifier are
assembled on lead frame, the epoxy package contains an IR
filter.
The demodulated output signal can be directly connected to
a microprocessor for decoding.
The TSOP324.., TSOP344.. series devices are optimized
to suppress almost all spurious pulses from energy saving
lamps like CFLs. The AGC4 used in the TSOP324..,
TSOP344.. may suppress some data signals. The
TSOP322.., TSOP348.. series are provided primarily for
compatibility with old AGC2 designs. New designs should
prefer the TSOP324.., TSOP344.. series containing the
newer AGC4.
These components have not been qualified according to
automotive specifications.
PARTS TABLE
AGC
LEGACY, FOR
LONG BURST REMOTE CONTROLS (AGC2)
RECOMMENDED FOR
LONG BURST CODES (AGC4)
30 kHz
TSOP34830
TSOP32230
TSOP34430
TSOP32430
33 kHz
TSOP34833
TSOP32233
TSOP34433
TSOP32433
Carrier
36 kHz
frequency 38 kHz
TSOP34836
TSOP34838
TSOP32236
TSOP32238
TSOP34436 (1)(2)(3)
TSOP34438 (4)(5)
TSOP32436 (1)(2)(3)
TSOP32438 (4)(5)
40 kHz
TSOP34840
TSOP32240
TSOP34440
TSOP32440
56 kHz
TSOP34856
TSOP32256
TSOP34456 (6)(7)
TSOP32456 (6)(7)
Package
Mold
Pinning
Dimensions (mm)
1 = OUT, 2 = GND, 3 = VS 1 = OUT, 2 = VS, 3 = GND 1 = OUT, 2 = GND, 3 = VS 1 = OUT, 2 = VS, 3 = GND
6.0 W x 6.95 H x 5.6 D
Mounting
Leaded
Application
Remote control
Best remote control code
(1) RC-5 (2) RC-6 (3) Panasonic (4) NEC (5) Sharp (6) r-step (7) Thomson RCA
Rev. 1.4, 22-Jul-16
1 Document Number: 82489
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
|
| |
 
TSOP322.., TSOP324.., TSOP344.., TSOP348..
www.vishay.com
Vishay Semiconductors
SUITABLE DATA FORMAT
This series is designed to suppress spurious output pulses
due to noise or disturbance signals. The devices can
distinguish data signals from noise due to differences in
frequency, burst length, and envelope duty cycle. The data
signal should be close to the device’s band-pass center
frequency (e.g. 38 kHz) and fulfill the conditions in the table
below.
When a data signal is applied to the product in the presence
of a disturbance, the sensitivity of the receiver is
automatically reduced by the AGC to insure that no spurious
pulses are present at the receiver’s output. Some examples
which are suppressed are:
• DC light (e.g. from tungsten bulbs sunlight)
• Continuous signals at any frequency
• Strongly or weakly modulated patterns from fluorescent
lamps with electronic ballasts (see Fig. 13 or Fig. 14).
0
16920
5 10 15
Time (ms)
20
Fig. 13 - IR Disturbance from Fluorescent Lamp
with Low Modulation
0
16921
5 10 15
Time (ms)
20
Fig. 14 - IR Disturbance from Fluorescent Lamp
with High Modulation
Minimum burst length
After each burst of length
a minimum gap time is required of
For bursts greater than
a minimum gap time in the data stream is needed of
Maximum number of continuous short bursts/second
NEC code
RC5/RC6 code
Thomson 56 kHz code
Sharp code
Suppression of interference from fluorescent lamps
TSOP322.., TSOP348..
10 cycles/burst
10 to 70 cycles
≥ 10 cycles
70 cycles
> 4 x burst length
1800
Yes
Yes
Yes
Yes
Mild disturbance patterns
are suppressed (example:
signal pattern of Fig. 13)
TSOP324.., TSOP344..
10 cycles/burst
10 to 35 cycles
≥ 10 cycles
35 cycles
> 10 x burst length
1500
Preferred
Preferred
Preferred
Preferred
Complex and critical disturbance patterns
are suppressed (example: signal pattern
of Fig. 14 or highly dimmed LCDs)
Notes
• For data formats with short bursts please see the datasheet for TSOP323.., TSOP325.., TSOP343.., TSOP345..
• For Sony 12, 15, and 20 bit IR codes please see the datasheet of TSOP34S40F, TSOP32S40F
Rev. 1.4, 22-Jul-16
5 Document Number: 82489
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for TSOP32230 electronic component. |
| Information | Total 10 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ TSOP32230.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| TSOP32230 | The function is IR Receiver Modules. Vishay | |
| TSOP32233 | The function is IR Receiver Modules. Vishay | |
| TSOP32236 | The function is IR Receiver Modules. Vishay | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
TSOP
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||