|
|
Número de pieza | AT49F1604 | |
Descripción | 16-megabit 5-volt Only Flash Memory | |
Fabricantes | ATMEL Corporation | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de AT49F1604 (archivo pdf) en la parte inferior de esta página. Total 18 Páginas | ||
No Preview Available ! Features
• 4.5V to 5.5V Read/Write
• Access Time – 90 ns
• Sector Erase Architecture
– Thirty 32K Word (64K byte) Sectors with Individual Write Lockout
– Eight 4K Word (8K byte) Sectors with Individual Write Lockout
– Two 16K Word (32K byte) Sectors with Individual Write Lockout
• Fast Word Program Time – 10 µs
• Fast Sector Erase Time – 200 ms
• Dual-plane Organization, Permitting Concurrent Read while Program/Erase
Memory Plane A: Eight 4K Word, Two 16K Word and Six 32K Word Sectors
Memory Plane B: Twenty-four 32K Word Sectors
• Erase Suspend Capability
– Supports Reading/Programming Data from Any Sector by Suspending Erase of
Any Different Sector
• Low-power Operation
– 60 mA Active
– 3 mA Standby
• DATA Polling, Toggle Bit, Ready/Busy for End of Program Detection
• RESET Input for Device Initialization
• Sector Program Unlock Command
• TSOP, CBGA and µBGA Package Options
• Top or Bottom Boot Block Configuration Available
Description
The AT49F16X4(T) is a 5.0-volt 16-megabit Flash memory organized as 1,048,576
words of 16 bits each or 2,097,152 bytes of 8 bits each. The x16 data appears on
I/O0 - I/O15; the x8 data appears on I/O0 - I/O7. The memory is divided into 40 sec-
tors for erase operations. The device is offered in 48-lead TSOP and 48-ball µBGA
packages. The device has CE and OE control signals to avoid any bus contention.
This device can be read or reprogrammed using a single 5.0V power supply, making it
ideally suited for in-system programming.
The device powers on in the read mode. Command sequences are used to place the
device in other operation modes such as program and erase. The device has the
(continued)
Pin Configurations
Pin Name
A0 - A19
CE
OE
WE
RESET
RDY/BUSY
I/O0 - I/O14
I/O15 (A-1)
BYTE
NC
DC
Function
Addresses
Chip Enable
Output Enable
Write Enable
Reset
READY/BUSY Output
Data Inputs/Outputs
I/O15 (Data Input/Output, Word Mode)
A-1 (LSB Address Input, Byte Mode)
Selects Byte or Word Mode
No Connect
Don’t Connect
16-megabit
(1M x 16/2M x 8)
5-volt Only
Flash Memory
AT49F1604
AT49F1604T
AT49F1614
AT49F1614T
Not Recommended for
New Designs
Rev. 0977J–04/00
1
1 page AT49F1604(T)/1614(T)
command is a one-bus cycle command, which does require
the plane address (determined by A18 and A19).
PRODUCT IDENTIFICATION: The product identification
mode identifies the device and manufacturer as Atmel. It
may be accessed by hardware or software operation. The
hardware operation mode can be used by an external pro-
grammer to identify the correct programming algorithm for
the Atmel product.
For details, see “Operating Modes” on page 9 (for hard-
ware operation) or “Software Product Identification
Entry/Exit” on page 14. The manufacturer and device
codes are the same for both modes.
DATA POLLING: The AT49F16X4(T) features Data Poll-
ing to indicate the end of a program cycle. During a
program cycle an attempted read of the last byte/word
loaded will result in the complement of the loaded data on
I/O7. Once the program cycle has been completed, true
data is valid on all outputs and the next cycle may begin.
During a sector erase operation, an attempt to read the
device will give a “0” on I/O7. Once the program or erase
cycle has completed, true data will be read from the device.
Data Polling may begin at any time during the program
cycle. Please see “Status Bit Table” on page 15 for more
details.
TOGGLE BIT: In addition to Data Polling, the
AT49F16X4(T) provides another method for determining
the end of a program or erase cycle. During a program or
erase operation, successive attempts to read data from the
same memory plane will result in I/O6 toggling between
one and zero. Once the program cycle has completed, I/O6
will stop toggling and valid data will be read. Examining the
toggle bit may begin at any time during a program cycle.
An additional toggle bit is available on I/O2, which can be
used in conjunction with the toggle bit that is available on
I/O6. While a sector is erase suspended, a read or a pro-
gram operation from the suspended sector will result in the
I/O2 bit toggling. Please see “Status Bit Table” on page 15
for more details.
RDY/BUSY: An open-drain Ready/Busy output pin pro-
vides another method of detecting the end of a program or
erase operation. RDY/BUSY is actively pulled low during
the internal program and erase cycles and is released at
the completion of the cycle. The open-drain connection
allows for OR-tying of several devices to the same
RDY/BUSY line.
HARDWARE DATA PROTECTION: The Hardware Data
Protection feature protects against inadvertent programs to
the AT49F16X4(T) in the following ways: (a) VCC sense: if
VCC is below 3.8V (typical), the program function is inhib-
ited. (b) VCC power-on delay: once VCC has reached the
VCC sense level, the device will automatically time out
10 ms (typical) before programming. (c) Program inhibit:
holding any one of OE low, CE high or WE high inhibits
program cycles. (d) Noise filter: pulses of less than 15 ns
(typical) on the WE or CE inputs will not initiate a program
cycle.
INPUT LEVELS: While operating with a 4.5V to 5.5V
power supply, the address inputs and control inputs (OE,
CE and WE) may be driven from 0 to 5.5V without
adversely affecting the operation of the device. The I/O
lines can only be driven from 0 to VCC + 0.6V.
5
5 Page AC Byte/Word Load Characteristics
Symbol
tAS, tOES
tAH
tCS
tCH
tWP
tDS
tDH, tOEH
tWPH
Parameter
Address, OE Setup Time
Address Hold Time
Chip Select Setup Time
Chip Select Hold Time
Write Pulse Width (WE or CE)
Data Setup Time
Data, OE Hold Time
Write Pulse Width High
AC Byte/Word Load Waveforms
WE Controlled
AT49F1604(T)/1614(T)
Min Max Units
10 ns
50 ns
0 ns
0 ns
100 ns
50 ns
10 ns
50 ns
CE Controlled
11
11 Page |
Páginas | Total 18 Páginas | |
PDF Descargar | [ Datasheet AT49F1604.PDF ] |
Número de pieza | Descripción | Fabricantes |
AT49F1604 | 16-megabit 5-volt Only Flash Memory | ATMEL Corporation |
AT49F1604T | 16-megabit 5-volt Only Flash Memory | ATMEL Corporation |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |