DataSheetWiki


ISL22316WM fiches techniques PDF

Intersil - Single Digitally Controlled Potentiometer

Numéro de référence ISL22316WM
Description Single Digitally Controlled Potentiometer
Fabricant Intersil 
Logo Intersil 





1 Page

No Preview Available !





ISL22316WM fiche technique
Data Sheet
ISL22316WM
Single Digitally Controlled Potentiometer (XDCP™)
November 11, 2011
FN6622.1
Low Noise, Low Power I2C® Bus, 128 Taps
The ISL22316WMUEP integrates a single digitally controlled
potentiometer (DCP) and non-volatile memory on a
monolithic CMOS integrated circuit.
The digitally controlled potentiometer is implemented with a
combination of resistor elements and CMOS switches. The
position of the wipers are controlled by the user through the
I2C bus interface. The potentiometer has an associated
volatile Wiper Register (WR) and a non-volatile Initial Value
Register (IVR) that can be directly written to and read by the
user. The contents of the WR controls the position of the
wiper. At power-up, the device recalls the contents of the
DCP’s IVR to the WR.
The DCP can be used as a three-terminal potentiometer or
as a two-terminal variable resistor in a wide variety of
applications including control, parameter adjustments and
signal processing.
Device Information
The specifications for an Enhanced Product (EP) device are
defined in a Vendor Item Drawing (VID), which is controlled
by the Defense Logistics Agency (DLA). “Hot-links” to the
applicable VID and other supporting application information
are provided on our website.
Pinout
SCL
SDA
A1
A0
SHDN
ISL22316WMUEP
(10 LD MSOP)
TOP VIEW
1 10
29
38
47
56
VCC
RH
RW
RL
GND
Features
• Specifications per DSCC VID V62/08603-01XB
• Full Mil-Temp Electrical Performance from -55°C to +125°C
• Controlled Baseline with One Wafer Fabrication Site and
One Assembly/Test Site
• Full Homogeneous Lot Processing in Wafer Fab
• No Combination of Wafer Fabrication Lots in Assembly
• Full Traceability Through Assembly and Test by
Date/Trace Code Assignment
• Enhanced Process Change Notification
• Enhanced Obsolescence Management
• Eliminates Need for Up-Screening a COTS Component
• 128 Resistor Taps
• I2C Serial Interface
- Two Address Pins, Up To Four Devices/Bus
• Non-volatile Storage of Wiper Position
• Wiper Resistance: 70Ω Typical @ 3.3V
• Shutdown Mode
• Shutdown Current 5µA Max
• Power Supply: 2.7V to 5.5V
• 10kΩ Total Resistance
• High Reliability
- Endurance: 1,000,000 Data Changes Per Bit Per
Register
- Register Data Retention:
- 10 years @ T +125°C
- 15 years @ T +90°C
- 50 years @ T +55°C
• 10 Ld MSOP
Ordering Information
VENDOR PART NUMBER
RESISTANCE OPTION
(Notes 1, 2)
VENDOR ITEM DRAWING PART MARKING
(kΩ)
ISL22316WMUEP
V62/08603-01XB
2316M
10
NOTES:
1. Add “-TK” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. Devices must be procured to the VENDOR PART NUMBER.
TEMP.
PKG.
RANGE (°C) PACKAGE DWG. #
-55 to +125 10 Ld MSOP M10.118
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) and XDCP are registered trademarks of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2007, 2011. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.

PagesPages 3
Télécharger [ ISL22316WM ]


Fiche technique recommandé

No Description détaillée Fabricant
ISL22316WM Single Digitally Controlled Potentiometer Intersil
Intersil

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche