DataSheetWiki


ISL22326WM fiches techniques PDF

Intersil - Dual Digitally Controlled Potentiometers

Numéro de référence ISL22326WM
Description Dual Digitally Controlled Potentiometers
Fabricant Intersil 
Logo Intersil 





1 Page

No Preview Available !





ISL22326WM fiche technique
Data Sheet
ISL22326WM
Dual Digitally Controlled Potentiometers (XDCP™)
November 11, 2011
FN6623.1
Low Noise, Low Power, I2C® Bus, 128 Taps
The ISL22326WMVEP integrates two digitally controlled
potentiometers (XDCP) and non-volatile memory on a
monolithic CMOS integrated circuit.
The digitally controlled potentiometers are implemented with
a combination of resistor elements and CMOS switches. The
position of the wipers are controlled by the user through the
I2C bus interface. Each potentiometer has an associated
volatile Wiper Register (WR) and a non-volatile Initial Value
Register (IVR) that can be directly written to and read by the
user. The contents of the WR controls the position of the
wiper. At power-up, the device recalls the contents of the two
DCP’s IVR to the corresponding WRs.
The DCPs can be used as three-terminal potentiometers or
as two-terminal variable resistors in a wide variety of
applications including control, parameter adjustments and
signal processing.
Device Information
The specifications for an Enhanced Product (EP) device are
defined in a Vendor Item Drawing (VID), which is controlled
by the Defense Logistics Agency (DLA). “Hot-links” to the
applicable VID and other supporting application information
are provided on our website.
Pinout
VCC
SHDN
RH0
RL0
RW0
A2
SCL
ISL22326WMVEP
(14 LD TSSOP)
TOP VIEW
1 14
2 13
3 12
4 11
5 10
69
78
A1
A0
RH1
RL1
RW1
GND
SDA
Features
• Specifications per DLA VID V62/08604-01XE
• Full Mil-Temp Electrical Performance from -55°C to +125°C
• Controlled Baseline with One Wafer Fabrication Site and
One Assembly/Test Site
• Full Homogeneous Lot Processing in Wafer Fab
• No Combination of Wafer Fabrication Lots in Assembly
• Full Traceability Through Assembly and Test by
Date/Trace Code Assignment
• Enhanced Process Change Notification
• Enhanced Obsolescence Management
• Eliminates Need for Up-Screening a COTS Component
• Two Potentiometers in One Package
• 128 Resistor Taps
• I2C Serial Interface
- Three Address Pins, Up To Eight Devices/Bus
• Non-volatile Storage of Wiper Position
• Wiper Resistance: 70Ω Typical @ 3.3V
• Shutdown Mode
• Shutdown Current 5µA Max
• Power Supply: 2.7V to 5.5V
• 10kΩ Total Resistance
• High Reliability
- Endurance: 1,000,000 Data Changes Per Bit Per
Register
- Register Data Retention:
- 10 years @ T +125°C
- 15 years @ T +90°C
- 50 years @ T +55°C
• 14 Ld TSSOP
Ordering Information
VENDOR PART NUMBER
RESISTANCE OPTION
(Notes 1, 2)
VENDOR ITEM DRAWING PART MARKING
(kΩ)
ISL22326WMVEP
V62/08604-01XE
22326 WMVEP
10
NOTES:
1. Add “-TK” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. Devices must be procured to the VENDOR PART NUMBER.
TEMP.
RANGE
(°C)
PKG.
PACKAGE DWG. #
-55 to +125 14 Ld TSSOP M14.173
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) and XDCP are registered trademarks of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2007, 2011. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.

PagesPages 3
Télécharger [ ISL22326WM ]


Fiche technique recommandé

No Description détaillée Fabricant
ISL22326WM Dual Digitally Controlled Potentiometers Intersil
Intersil

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche