|
|
Número de pieza | SURTA1500XL | |
Descripción | Smart-UPS RT Uninterruptible Power Supply User Manual | |
Fabricantes | APC | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SURTA1500XL (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
No Preview Available ! APC Smart-UPS® RT SURTA1500XL/SURTA1500XLJ/SURTA2000XL
Uninterruptible Power Supply User Manual
Introduction/Before Installation
About this Manual
The APC Smart-UPS® RT (SURTA1500XL, SURTA1500XLJ, and SURTA2000XL) is a high-
performance, Uninterruptible Power Supply (UPS) designed to prevent blackouts, brownouts, sags
and surges from reaching your computers, servers, and other sensitive electronic equipment.
This manual describes procedures on how to properly unpack and install the UPS, connect the battery
and equipment, configure accessories, and start up the system.
Illustrations are representative. Your configuration, including components and optional APC equip-
ment, may be different from the models shown in this manual. The user manual is accessible from the
supplied CD and the APC web site, www.apc.com.
Contact Information
Refer to www.apc.com to contact APC or for additional information about this product.
Safety Information
Read the Safety Guide before you begin the installation, operate the UPS, or
perform equipment maintenance. Failure to comply with safety instructions
Warning could result in bodily injury or equipment damage.
Unpacking and Equipment Placement
The UPS is heavy. Two people are required to lift the UPS.
Select a location sturdy enough to handle the weight of the UPS.
Heavy
1. Unpack the equipment. The packaging is recyclable; save it for reuse or dispose of it properly.
2. Inspect the equipment upon receipt. Notify the carrier and dealer if there is damage.
3. Check the package contents:
• UPS and front bezel
• UPS literature kit containing:
– product documentation
– safety information
– warranty information
120 V models:
• PowerChute® CD
• Serial and USB
communication
cables
100 V models:
• Serial
communication
cable
4. Place the UPS where it will be used.
– Ensure that air vents on the front and rear of the UPS are not blocked.
1 page Terminal Mode Configuration
Connect Power and Start Up the UPS
The UPS battery charges when it is connected to utility power and will charge to 90%
capacity within three hours. Do not expect full battery run capability from a new bat-
tery or after On Battery operation (see “On Battery Operation” on page 7) until the
battery recharges.
Note To use the UPS as a master ON/OFF switch, ensure all connected equipment is
switched on. The equipment will not be powered until the UPS is turned on.
1. Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension cords.
a. Check to ensure that the Site Wiring Fault LED light on the back of the UPS is NOT
illuminated (On position).
b. If the LED light is on, the outlet is incorrectly wired. Check with a licensed electrician to
ensure that the outlet is properly wired.
2. To power up the UPS, press the button on the front panel.
3. Turn on all connected equipment.
For Additional Computer System Security
For additional computer system security, install PowerChute® Business Edition Smart-UPS® monitor-
ing software. Refer to the software CD included in the literature kit for instructions.
Terminal Mode Configuration
Terminal mode can only be used with the serial cable. If using a USB cable, disconnect
the USB cable from the UPS, and connect the serial cable to the UPS before using the
Note terminal program.
Shown below is an example of how to use terminal mode to configure the number of external battery
packs. See “Configuration Settings” on page 8 for additional information.
1. Exit the PowerChute Business Edition software.
a. From the windows PC desktop, select START => Settings => Control Panel => Administrative
Tools => Services.
b. Select APC PCBE Server and APC PCBE Agent. Right click the mouse and select Stop.
2. Open a terminal program. Example: HyperTerminal
From the computer desktop, select START => Programs => Accessories => Communication =>
HyperTerminal.
3. Double-click the HyperTerminal icon.
a. Follow the prompts to choose a name and select an icon. Disregard the message, “...must
install a modem,” if it is displayed. Click OK.
Smart-UPS RT SURTA1500XL/SURTA1500XLJ/SURTA2000XL Uninterruptible Power Supply User Manual 5
5 Page Storage, Maintenance, Transport, and Service
Battery Replacement Instructions
If the battery needs replacement, follow the steps below to remove the battery from the UPS.
1. Disconnect the battery. See step 3 in “Transporting the UPS to Another Location” on page 10.
2. Grab the battery handle to pull the battery out of the frame.
3. To disengage the battery from the frame, push in the two tabs on the side of the battery and
slide it out of the UPS.
4. Refer to the battery replacement instruction sheet to install the replacement battery in the UPS.
Service
Always DISCONNECT THE BATTERY before shipping the UPS to be in
compliance with U.S. Department of Transportation (DOT) regulations.
Caution
If the UPS requires service do not return it to the dealer. Follow these steps:
1. Review the problems discussed in “Troubleshooting,” beginning on page 12 to eliminate
common problems.
2. If the problem persists, contact APC Customer Service through the APC web site,
www.apc.com.
– Note the model number of the UPS, the serial number, and the date purchased. If you call APC
Customer Service, a technician will ask you to describe the problem and attempt to solve it
over the phone. If this is not possible, the technician will issue a Returned Material
Authorization Number (RMA#).
– If the UPS is under warranty, repairs are free.
– Procedures for servicing or returning products may vary internationally. Refer to the APC web
site, www.apc.com for country specific instructions.
3. Disconnect the battery for transport. See step 3 in “Transporting the UPS to Another Location”
on page 10.
4. Pack the UPS and front bezel in its original packaging to avoid damage in transit. If this is not
available, refer to www.apc.com for information about obtaining a new set. Never use Styrofoam
beads for packaging. Damage sustained in transit is not covered under warranty.
5. Mark the RMA# on the outside of the package.
6. Return the UPS by insured, prepaid carrier to the address given to you by Customer Service.
Smart-UPS RT SURTA1500XL/SURTA1500XLJ/SURTA2000XL Uninterruptible Power Supply User Manual 11
11 Page |
Páginas | Total 16 Páginas | |
PDF Descargar | [ Datasheet SURTA1500XL.PDF ] |
Número de pieza | Descripción | Fabricantes |
SURTA1500XL | Smart-UPS RT Uninterruptible Power Supply User Manual | APC |
SURTA1500XLJ | Smart-UPS RT Uninterruptible Power Supply User Manual | APC |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |