PDF PIC16LF1705 Data sheet ( Hoja de datos )

Número de pieza	PIC16LF1705
Descripción	Cost-Effective 8-Bit Intelligent Analog Flash Microcontrollers
Fabricantes	Microchip
Logotipo
Hay una vista previa y un enlace de descarga de PIC16LF1705 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas
No Preview Available ! PIC16(L)F1705/9 Cost-Effective 8-Bit Intelligent Analog Flash Microcontrollers Description PIC16(L)F1705/9 microcontrollers combine Intelligent analog integration with low cost and extreme low-power (XLP) to suit a variety of general purpose applications. These 14- and 20-pin devices deliver on-chip op amps, core independent peripherals (CLC and COG), Peripheral Pin Select and Zero-Cross Detect, providing for increased design flexibility. Core Features • C Compiler Optimized RISC Architecture • Only 49 Instructions • Operating Speed: - 0-32 MHz - 125 ns minimum instruction cycle • Interrupt Capability • 16-Level Deep Hardware Stack • Four 8-bit Timers • One 16-bit Timer • Power-on Reset (POR) • Power-up Timer (PWRT) • Low-Power Brown-Out Reset (LPBOR) • Programmable Watchdog Timer (WDT) up to 256s • Programmable Code Protection Memory • 8 Kwords Flash Program Memory • 1024 Bytes Data SRAM Memory • Direct, Indirect and Relative Addressing modes Operating Characteristics • Operating Voltage Range: - 1.8V to 3.6V (PIC16LF1705/9) - 2.3V to 5.5V (PIC16F1705/9) • Temperature Range: - Industrial: -40°C to 85°C - Extended: -40°C to 125°C eXtreme Low-Power (XLP) Features • Sleep mode: 50 nA @ 1.8V, typical • Watchdog Timer: 500 nA @ 1.8V, typical • Secondary Oscillator: 500 nA @ 32 kHz • Operating Current: - 8 uA @ 32 kHz, 1.8V, typical - 32 uA/MHz @ 1.8V, typical Digital Peripherals • Configurable Logic Cell (CLC): - Integrated combinational and sequential logic • Complementary Output Generator (COG): - Rising/falling edge dead-band control/ blanking • Capture/Compare/PWM (CCP) module • PWM: Two 10-bit Pulse-Width Modulators • Serial Communications: - SPI, I2C™, RS-232, RS-485, LIN compatible - Auto-Baud Detect, auto-wake-up on start • Up to 17 I/O Pins plus One Input-Only Pin: - Individually programmable pull-ups - Slew rate control - Interrupt-on-change with edge-select • Peripheral Pin Select (PPS): - Enables pin mapping of digital I/O • Timer0: 8-Bit Timer/Counter with 8-Bit Prescaler • Enhanced Timer1: - 16-bit timer/counter with prescaler - External Gate Input mode - Low-power 32 kHz secondary oscillator driver • Timer2/4/6: 8-Bit Timer/Counter with 8-Bit Period Register, Prescaler and Postscaler Intelligent Analog Peripherals • Operational Amplifiers: - Two configurable rail-to-rail op amps - Selectable internal and external channels - 2 MHz gain bandwidth product • High-Speed Comparators: - Two comparators - 50 ns response time - Rail-to-rail inputs • 10-Bit Analog-to-Digital Converter (ADC): - Up to 12 external channels - Conversion available during Sleep - Temperature indicator  2013-2015 Microchip Technology Inc. DS40001729B-page 1 1 page Pin Allocation Tables TABLE 1: 14/16-PIN ALLOCATION TABLE (PIC16(L)F1705) RA0 13 12 AN0 VREF- C1IN+ RA1 12 11 AN1 VREF+ C1IN0- C2IN0- RA2 11 10 AN2 — — RA3 4 3—— — — DAC1OUT1 — — — — — — —— — DAC1OUT2 ZCD T0CKI(1) — — — — —— — — —— — — —— — COGIN(1) — — — — —— — IOC Y — IOC Y — INT(1) Y IOC — IOC Y RA4 3 2 AN3 — — — — — T1G(1) — — — — — — SOSCO RA5 2 1—— — — — — T1CKI(1) — — — — — CLCIN3(1) SOSCI RC0 10 9 AN4 — C2IN+ OPA1IN+ — — —— — — SCK(1) — — SCL(3) RC1 9 8 AN5 — C1IN1- OPA1IN- — — —— — — SDI(1) — CLCIN2(1) C2IN1- SDA(3) RC2 8 7 AN6 — C1IN2- OPA1OUT — — —— — — —— — C2IN2- RC3 7 6 AN7 — C1IN3- OPA2OUT C2IN3- — — — CCP2(1) — — SS(1) — CLCIN0(1) RC4 6 5—— — OPA2IN- — — —— — — — CK(1) CLCIN1(1) RC5 5 4—— — OPA2IN+ — — — CCP1(1) — — — RX(1,3) — VDD 1 16 — — — — — — — — — — —— — VSS 14 13 — — — — — — — — — — —— — ——— — C1OUT — — — — CPP1 PWM3OUT COGA SDA(3) CK CLC1OUT ——— OUT(2) ——— — C2OUT —— — — — — — CPP2 PWM4OUT COGB SCL(3) DT(3) CLC2OUT — — —— — COGC SDO TX CLC3OUT ——— — — — — — —— — COGD SCK — — Note 1: 2: 3: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers. See Register 12-1. All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers. See Register 12-3. These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections. IOC IOC IOC IOC IOC IOC IOC IOC — — — — — — Y Y Y Y Y Y Y Y — — — — — — ICSPDAT ICSPCLK — MCLR VPP CLKOUT OSC2 CLKIN OSC1 — — — — — — VDD VSS — — — — 5 Page PIC16(L)F1705/9 TABLE 1-2: PIC16(L)F1705 PINOUT DESCRIPTION Name Function Input Type Output Type Description RA0/AN0/VREF-/C1IN+/ DAC1OUT/ICSPDAT RA0 TTL/ST CMOS General purpose I/O. AN0 AN — ADC Channel 0 input. VREF- AN — ADC Negative Voltage Reference input. C1IN+ AN — Comparator C1 positive input. DAC1OUT — AN Digital-to-Analog Converter output. ICSPDAT ST CMOS ICSP™ Data I/O. RA1/AN1/VREF+/C1IN0-/C2IN0-/ ICSPCLK RA1 AN1 TTL/ST AN CMOS General purpose I/O. — ADC Channel 1 input. VREF+ C1IN0- AN AN — ADC Voltage Reference input. — Comparator C2 negative input. C2IN0- AN — Comparator C3 negative input. ICSPCLK ST — Serial Programming Clock. RA2/AN2/DAC1OUT2/ZCD/ T0CKI(1)/COGIN(1)/INT(1) RA2 TTL/ST CMOS General purpose I/O. AN2 AN — ADC Channel 2 input. DAC1OUT2 — AN Digital-to-Analog Converter output. ZCD — AN Zero-Cross Detection Current Source/Sink. T0CKI TTL/ST — Timer0 clock input. COGIN TTL/ST CMOS Complementary Output Generator input. INT TTL/ST — External interrupt. RA3/MCLR/VPP RA3 TTL/ST CMOS General purpose I/O. MCLR ST — Master Clear with internal pull-up. RA4/AN3/T1G(1)/SOSCO/ OSC2/CLKOUT VPP RA4 AN3 HV TTL/ST AN — CMOS — Programming voltage. General purpose I/O. ADC Channel 3 input. T1G TTL/ST — Timer1 gate input. SOSCO XTAL XTAL Secondary Oscillator Connection. OSC2 — XTAL Crystal/Resonator (LP, XT, HS modes). RA5/T1CKI(1)/SOSCI/ CLCIN3(1)/OSC1/CLKIN CLKOUT RA5 T1CKI — TTL/ST TTL/ST CMOS CMOS — FOSC/4 output. General purpose I/O. Timer1 clock input. SOSCI XTAL XTAL Secondary Oscillator Connection. CLCIN3 TTL/ST — Configurable Logic Cell source input. OSC1 — XTAL Crystal/Resonator (LP, XT, HS modes). CLKIN ST — External clock input (EC mode). Legend: AN = Analog input or output CMOS= CMOS compatible input or output OD = Open-Drain TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C™= Schmitt Trigger input with I2C HV = High Voltage XTAL = Crystal levels Note 1: 2: 3: Default peripheral input. Input can be moved to any other pin with the PPS input selection registers. See Register 12-1. All pin outputs default to PORT latch data. Any pin can be selected as a digital peripheral output with the PPS output selection registers. See Register 12-3. These I2C functions are bidirectional. The output pin selections must be the same as the input pin selections.  2013-2015 Microchip Technology Inc. DS40001729B-page 11 11 Page

Páginas	Total 30 Páginas
PDF Descargar	[ Datasheet PIC16LF1705.PDF ]

Hoja de datos destacado

Número de pieza	Descripción	Fabricantes
PIC16LF1703	14/20-Pin 8-Bit Advanced Analog Flash Microcontrollers	Microchip Technology
PIC16LF1704	14/20-Pin 8-Bit Advanced Analog Flash Microcontrollers	Microchip
PIC16LF1705	Cost-Effective 8-Bit Intelligent Analog Flash Microcontrollers	Microchip
PIC16LF1707	14/20-Pin 8-Bit Advanced Analog Flash Microcontrollers	Microchip Technology

Número de pieza	Descripción	Fabricantes
SLA6805M	High Voltage 3 phase Motor Driver IC.	Sanken
SDC1742	12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.	Analog Devices

DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.

DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar