|
|
Número de pieza | MG26P700 | |
Descripción | USB Voltage Position Controller | |
Fabricantes | Megawin | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de MG26P700 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
No Preview Available ! 笙泉科技股份有限公司
Megawin Technology Co., Ltd.
Version: 1.05
MG26P700
Datasheet
USB Voltage Position Controller with Quick Charge
This document information is the intellectual property of Megawin Technology.
Megawin Technology Co., Ltd. 2011 All right reserved.
QP-7300-03D
1/8
Version 1.05
1 page MG26P700 Datasheet
Version 1.05
3. Pin Configurations
3.1 SOP10 – MG26P700AS10
VDD SW/BLD
SEL
S1
GND
BC EN
D+
D-
S2 S3
Pin Name
Figure 3-1 package SOP10
Type Description
1 VDD
P Positive power pins
2 SEL
B To set power consumption either Apple 10W or 12W.
3 S1
4 GND
Quick Charge Voltage Select 1. Enable 9V, 12V, 20V. Check the detail
B
in lookup table. To use with an external resistor to pull down feedback
voltage for 9V output. Connect LED on this pin and control the sink
current under 2mA for QC 9V indicator.
G Ground pin
5 S2
6 S3
7 D-
Quick Charge Voltage Select 2. Enable 9V, 12V, 20V. Check the detail
B
in lookup table. To use with an external resistor to pull down feedback
voltage for 12V output. Connect LED on this pin and control the sink
current under 2mA for QC 12V indicator.
B Quick Charge Voltage Select 3. Enable 9V, 12V, 20V. Check the detail
in lookup table. To use with an external resistor to pull down feedback
voltage for 20V output. Connect LED on this pin and control the sink
current under 2mA for QC 20V indicator.
B USB D- In.
8 D+
B USB D+ In.
9 BC_EN
B
To drive external MOSFET to induce 200 ohm between D-/D+ line for
BC1.2 protocol
10 SW/BLD
B 5V Output indicator. Optional discharge control when high voltage
reduces to low voltage. When the transient time longer than 500ms, it
can use this pin to driver an external MOSFET to enable discharge path
to speed up the discharge time.
Note: In the “Type” field,
“B” means bi-direction.
“P” means Power, “G” means Ground.
This document information is the intellectual property of Megawin Technology.
Megawin Technology Co., Ltd. 2011 All right reserved.
QP-7300-03D
5/8
5 Page |
Páginas | Total 8 Páginas | |
PDF Descargar | [ Datasheet MG26P700.PDF ] |
Número de pieza | Descripción | Fabricantes |
MG26P700 | USB Voltage Position Controller | Megawin |
MG26P701 | USB Quick Charge | Megawin |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |