|
|
PDF LS010B7DH05 Data sheet ( Hoja de datos )
| Número de pieza | LS010B7DH05 | |
| Descripción | LCD Module | |
| Fabricantes | Sharp | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LS010B7DH05 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
1 page  
【Set-Design Precautions】
SPEC No.
LD-27602A
MODEL No.
LS010B7DH05
PAGE
3
(1) Disassembly of the LCD panel in any way voids the warranty and may permanently damage the LCD panel.
(2) Do not expose the side of LCD panel and gate driver, etc. on the panel (circuit area outside panel display area)
to light as it may not operate properly. Design that shields the side of LCD panel and gate driver, etc. from
light is required when mounting the LCD module.
(3) Support for the LCD panel should be carefully designed to avoid the outside of stress specification on glass
surface.
Be sure to design the cabinet so that the module can be assembled without any extra stress such as warp or twist.
(4) It causes an irregular display and the defective indication, etc., when always put constant pressure on the back
of the module. Please do not make the structure to press the back of the module.
(5) In case of attaching a cover glass or touch panel to the front surface, use appropriate measures to avoid
degrading optical performance.
(6) To prevent loss of uniformity and prevent the introduction of contamination to the optical path of the LCD panel,
please use fine-pitch filters in the air flow of forced ventilation.
(7) Be sure to follow the absolute maximum rating in the specification. The design should consider the surrounding
temperature, the fluctuating input signal, and tolerance of the electronic parts. Exceeding values is possible to
cause worse characteristic such as burn and/or broken of the parts on LCD module.
(8) Be sure to use LCD module within the recommended Electrical Characteristics and Timing Characteristics of
Input Signals conditions. Operating module out of the recommended range is not guaranteed even if it is in the
absolute maximum rating.
(9) Follow the power, signal, and supply voltage sequence which the publication indicates, regarding on-off input
signal after power on of LCD module.
(10) According to the using application, power circuit protection is recommended at module failure.
(11) When handling LCD modules and assembling them into the cabinet, please avoid long-term storage in the
environment of oxidization or deoxidization gas. The use of materials such as reagent, solvent, adhesive, resin,
etc. which generate these gasses, may cause corrosion and discoloration of the modules. Do not use the
LCD module under such environment.
(12) To avoid picture uniformity failure, do not put a seal or an adhesive material on the LCD panel surface.
(13) Protection film is attached to the module surface to prevent it from being scratched .Peel the film off slowly,
just before the use, with strict attention to electrostatic charges. Blow off 'dust' on the polarizer by using an
ionized nitrogen.
After peeling the protection film off, please do not reattach to the front polarizer. If you reattach and store it
long time, surface of the front polarizer changes in quality and it may cause display non-uniformity issue.
(14) Panel is susceptible to mechanical stress and such stress may affect the display. Place the LCD panel on flat
surface to avoid stress caused by twist, bend, etc.
©Copyright 2015 SHARP All rights reserved
5 Page 
SPEC No.
LD-27602A
MODEL No.
LS010B7DH05
PAGE
9
1. Applocable Memory liquid crystal display
This TFT-LCD module is a reflective active-matrix with slightly transmissive memory liquid crystal display
module with CG silicone thin film transistor. Module outline is indicated in Figure 14-1
2. Characteristics
・ A reflective active-matrix with slightly transmissive panel of white and black
・ 0.96” screen has 192x192 resolusion.
・ The outward form is an octagon. Active Area is circle.
・ Display control by serial data signal communication.
・ Arbitrary line data renewable.
・ 1bit internal memory for data storage within the panel.
・ Thin, light-weight and compact module with monolithic technology.
・ Super low power consumption TFT panel.
・ With FPC (Applicable connecter : Ref to recommended connecter on Page 28)
3. Mechanical Specification
Table 3-1 Module mechanical specification
Item Specification
Screen size
φ24.384 (0.96”) diameter
Dot configuration
192 (H) × 192 (V)
Dot pitch
0.127 (H) × 0.127 (V)
Pixel Array
Stripe
Outline Dimension
29.7 (W) × 30.5 (H) × 1.645 (D)
Mass
3.0(max)
Surface Hardness
at least 3H (initial)
Surface treatment
AG
(Note) Detail dimension and tolerance are shown in Figure.14-1
unit
mm
Dot
mm
-
mm
g
Pencil hardness
©Copyright 2015 SHARP All rights reserved
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet LS010B7DH05.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LS010B7DH01 | LCD Module | Sharp |
| LS010B7DH05 | LCD Module | Sharp |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |