|
|
PDF MI0177JT-1 Data sheet ( Hoja de datos )
| Número de pieza | MI0177JT-1 | |
| Descripción | LCD Module | |
| Fabricantes | MULTI-INNO TECHNOLOGY | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MI0177JT-1 (archivo pdf) en la parte inferior de esta página. Total 22 Páginas | ||
|
No Preview Available !
MULTI-INNO TECHNOLOGY CO., LTD.
www.multi-inno.com
LCD MODULE SPECIFICATION
Model : MI0177JT-1
For Customer's Acceptance:
Customer
Approved
Comment
Revision
Engineering
Date
Our Reference
1.2
2012-07-23
1 page  
MODULE NO.: MI0177JT-1
EXTERNAL DIMENSIONS
Ver 1.2
MULTI-INNO TECHNOLOGY CO.,LTD.
P.5
5 Page 
MODULE NO.: MI0177JT-1
Ver 1.2
RELIABILITY TEST CONDITIONS
No. Test Item
Test Condition
Inspection after test
1 High Temperature Storage 80
2 /120hours
2 Low Temperature Storage -30
2 /120hours
3 High Temperature Operating 70
2 /120 hours
4 Low Temperature Operating -20
2 /120 hours
5 Temperature Cycle
5 Damp Proof Test
-20
2 ~25~70
2 10cycles
(30min.) (5min.) (30min.)
40
5 90%RH/120 hours
Frequency10Hz~55Hz~10Hz
Inspection
after
2~4hours storage at
room temperature, the
sample shall be free from
7 Vibration Test
8 Dropping test
9 ESD test
Amplitude1.5mm,
X Y Z direction for total 3hours
(Packing condition)
Drop to the ground from 1m height,
one time, every side of carton.
(Packing condition)
Voltage:±8KV R: 330Ω C: 150pF
Air discharge, 10time
defects:
1.Air bubble in the LCD;
2.Sealleak;
3.Non-display;
4.missing segments;
5.Glass crack;
6.Current Idd is twice
higher than initial value.
7. The surface shall be
10 Hitting test
1,000,000 times in the same point,
Hitting pad: tip R3.75 mm, Silicone
rubber, Hardness:40 deg.; Load:
2.45N; Hitting speed: Twice/sec;
Electric load: None;
Test area should be at 1.8 mm inside of
touch panel view area
100, 000 times minimum
free from damage.
8.Linearity must be no
more than 1.5% by the
linearity tester.
9.The
Electrical
characteristics
requirements shall be
satisfied.
Hitting pad: tip R0.8 mm Plastic pen;
11
Pen sliding durability test
Load:1.47N; Sliding speed: 60
mm/sec; Electric load: None
Test area should be at 1.8 mm inside of
touch panel view area
Remark:
1.The test samples should be applied to only one test item.
2.Sample size for each test item is 5~10pcs.
3.For Damp Proof Test, Pure water(Resistance10MΩ) should be used.
4.In case of malfunction defect caused by ESD damage, if it would be recovered to normal state after
resetting, it would be judged as a good part.
5.EL evaluation should be excepted from reliability test with humidity and temperature: Some defects
such as black spot/blemish can happen by natural chemical reaction with humidity and Fluorescence EL
has.
6.Failure Judgment Criterion: Basic Specification, Electrical Characteristic, Mechanical Characteristic,
Optical Characteristic.
MULTI-INNO TECHNOLOGY CO.,LTD.
P.11
11 Page | ||
| Páginas | Total 22 Páginas | |
| PDF Descargar | [ Datasheet MI0177JT-1.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MI0177JT-1 | LCD Module | MULTI-INNO TECHNOLOGY |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |