AT90S8515-8PI Datasheet PDF - ATMEL Corporation
| Part Number | AT90S8515-8PI | |
| Description | 8-Bit Microcontroller with 8K bytes In-System Programmable Flash | |
| Manufacturers | ATMEL Corporation | |
| Logo |  |
|
|
There is a preview and AT90S8515-8PI download ( pdf file ) link at the bottom of this page. Total 70 Pages | ||
Preview 1 page No Preview Available !
Features
• Utilizes the AVR® RISC Architecture
• AVR – High-performance and Low-power RISC Architecture
– 118 Powerful Instructions – Most Single Clock Cycle Execution
– 32 x 8 General-purpose Working Registers
– Up to 8 MIPS Throughput at 8 MHz
• Data and Nonvolatile Program Memory
– 8K Bytes of In-System Programmable Flash
Endurance: 1,000 Write/Erase Cycles
– 512 Bytes of SRAM
– 512 Bytes of In-System Programmable EEPROM
Endurance: 100,000 Write/Erase Cycles
– Programming Lock for Flash Program and EEPROM Data Security
• Peripheral Features
– One 8-bit Timer/Counter with Separate Prescaler
– One 16-bit Timer/Counter with Separate Prescaler
Compare, Capture Modes and Dual 8-, 9-, or 10-bit PWM
– On-chip Analog Comparator
– Programmable Watchdog Timer with On-chip Oscillator
– Programmable Serial UART
– Master/Slave SPI Serial Interface
• Special Microcontroller Features
– Low-power Idle and Power-down Modes
– External and Internal Interrupt Sources
• Specifications
– Low-power, High-speed CMOS Process Technology
– Fully Static Operation
• Power Consumption at 4 MHz, 3V, 25°C
– Active: 3.0 mA
– Idle Mode: 1.0 mA
www.DataSheet4U.com
– Power-down Mode: <1 µA
• I/O and Packages
– 32 Programmable I/O Lines
– 40-lead PDIP, 44-lead PLCC and TQFP
• Operating Voltages
– 2.7 - 6.0V for AT90S8515-4
– 4.0 - 6.0V for AT90S8515-8
• Speed Grades
– 0 - 4 MHz for AT90S8515-4
– 0 - 8 MHz for AT90S8515-8
8-bit
Microcontroller
with 8K Bytes
In-System
Programmable
Flash
AT90S8515
Rev. 0841G–09/01
1
|
| |
 
RESET
XTAL1
XTAL2
ICP
OC1B
ALE
AT90S8515
current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset
condition becomes active, even if the clock is not active.
Port D also serves the functions of various special features of the AT90S8515 as listed
on page 73.
Reset input. A low level on this pin for more than 50 ns will generate a reset, even if the
clock is not running. Shorter pulses are not guaranteed to generate a reset.
Input to the inverting oscillator amplifier and input to the internal clock operating circuit.
Output from the inverting oscillator amplifier.
ICP is the input pin for the Timer/Counter1 Input Capture function.
OC1B is the output pin for the Timer/Counter1 Output CompareB function.
ALE is the Address Latch Enable used when the External Memory is enabled. The ALE
strobe is used to latch the low-order address (8 bits) into an address latch during the first
access cycle, and the AD0 - 7 pins are used for data during the second access cycle.
0841G–09/01
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for AT90S8515-8PI electronic component. |
| Information | Total 70 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ AT90S8515-8PI.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| AT90S8515-8PC | The function is 8-Bit Microcontroller with 8K bytes In-System Programmable Flash. ATMEL Corporation | |
| AT90S8515-8PI | The function is 8-Bit Microcontroller with 8K bytes In-System Programmable Flash. ATMEL Corporation | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
AT90
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||