DataSheetWiki


6N139 fiches techniques PDF

Siemens Semiconductor Group - LOW INPUT CURRENT/ HIGH GAIN OPTOCOUPLER

Numéro de référence 6N139
Description LOW INPUT CURRENT/ HIGH GAIN OPTOCOUPLER
Fabricant Siemens Semiconductor Group 
Logo Siemens Semiconductor Group 





1 Page

No Preview Available !





6N139 fiche technique
FEATURES
• High Current Transfer Ratio, 800%
• Low Input Current, 0.5mA
• High Output Current, 60mA
• Isolation Test Voltage, 2500 VACRMS
• TTL Compatible Output, VOL=0.1 V
• High Common Mode Rejection, 500V/µsec.
• Adjustable Bandwidth–Access to Base
• Standard Molded Dip Plastic Package
• Underwriters Lab File #E52744
APPLICATIONS
• Logic Ground Isolation–TTL/TTL, TTL/CMOS,
CMOS/CMOS, CMOS/TTL
• EIA RS 232C Line Receiver
• Low Input Current Line Receiver–Long Lines,
Party Lines
• Telephone Ring Detector
• 117 VAC Line Voltage Status Indication–Low
Input Power Dissipation
• Low Power Systems–Ground Isolation
DESCRIPTION
High common mode transient immunity and very
high current ratio together with 2500 VAC insulation
are achieved by coupling an LED with an integrated
high gain photo detector in an eight pin dual-in-line
package. Separate pins for the photodiode and out-
put stage enable TTL compatible saturation volt-
ages with high speed operation. Photodarlington
operation is achieved by tying the VCC and VO ter-
minals together. Access to the base terminal allows
adjustment to the gain bandwidth.
The 6N138 is ideal for TTL applications since the
300% minimum current transfer ratio with an LED
current of 1.6 mA enables operation with one unit
load-in and one unit load-out with a 2.2 Kpull-up
resistor.
The 6N139 is best suited for low power logic appli-
cations involving CMOS and low power TTL. A
400% current transfer ratio with only 0.5 mA of LED
current is guaranteed from 0°C to 70°C.
Caution:
Due to the small geometries of this device, it should be
handled with Electrostatic Discharge (ESD) precau-
tions. Proper grounding would prevent damage further
and/or degradation which may be induced by ESD.
6N138
6N139
LOW INPUT CURRENT, HIGH GAIN
OPTOCOUPLER
Dimensions in inches (mm)
43 21
.268 (6.81)
.255 (6.48)
56 78
.390 (9.91)
.379 (9.63)
.045 (1.14)
.030 (.76)
Pin
One
I.D. NC 1
Anode 2
Cathode 3
NC 4
8 VCC
7 VB
6 V0
5 GND
.305 typ.
(7.75) typ.
4°
Typ.
.022 (.56)
.018 (.46)
.150 (3.81)
.130 (3.30)
.040 (1.02)
.030 (.76 )
.100 (2.54) Typ.
10 °
Typ.
3°–9°.012 (.30)
.008 (.20)
.135 (3.43)
.115 (2.92)
Maximum Ratings
Reverse Input Voltage ..........................................................................5 V
Supply and Output Voltage, VCC (pin 8-5), VO (pin 6-5)
6N138 ................................................................................... –0.5 to 7 V
6N139 ................................................................................. –0.5 to 18 V
Emitter-Base Reverse Voltage (pin 5-7) ............................................0.5 V
Average Input Current.....................................................................20 mA
Peak Input Current (50% Duty Cycle–1 ms pulse width) ................40 mA
Peak Transient Input Current (tp1 µsec, 300 pps ...........................1.0 A
Output Current IO (pin 6) .................................................................60 mA
Derate linearly above 25°C, free air temperature at 0.7 mA/°C
Input Power Dissipation .................................................................35 mW
Derate linearly above 50%, free air temperature at 0.7 mW/°C
Output Power Dissipation.............................................................100 mW
Derate linearly above 25°C, free air temperature at 0.2 mA/°C
Isolation Test Voltage........................................................... 2500 VACRMS
Isolation Resistance
VIO=500 V, TA=25°C .........................................................................≥1012
VIO=500 V, TA=100°C.......................................................................≥1011
Storage Temperature......................................................–55°C to +125°C
Operating Temperature ..................................................–55°C to +100°C
Lead Soldering Temperature (t=10 sec.) ........................................260°C
5–1

PagesPages 2
Télécharger [ 6N139 ]


Fiche technique recommandé

No Description détaillée Fabricant
6N134 Hermetically Sealed / High Speed / High CMR / Logic Gate Optocouplers Hewlett-Packard
Hewlett-Packard
6N135 High Speed Optocouplers LITE-ON
LITE-ON
6N135 High Speed Optocoupler Vishay
Vishay
6N135 IRED & PHOTO IC (DIGITAL LOGIC ISOLATION) Toshiba Semiconductor
Toshiba Semiconductor

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche