DataSheetWiki


KC778B fiches techniques PDF

COMedia - Master PIR Control Chip

Numéro de référence KC778B
Description Master PIR Control Chip
Fabricant COMedia 
Logo COMedia 





1 Page

No Preview Available !





KC778B fiche technique
KC778B
Master PIR Control Chip (MPCC)
Specification
___________________________________________________________________________
General :
The MPCC has been designed for easy implementation
of AC control functions that use a Passive Infra-Red
(PIR) motion detector. Due to its high sensitivity and
reliability, it is also widely used in security product.
Minimum external component
High senstivity
High RFI immunity
Daylight adjustment
Off delay timer
20 pin DIP
Features:
A) Circuit design maximizes performance while minimizing external component count and board layout space.
B) Low cost solution for PIR motion control switching applications.
C) High sensitivity PIR input with special noise cancellation circuitry.
D) Choice of two PIR gain settings: 62 db and 68 db.
E) Adjustable PIR sensitivity.
F) Internal switched capacitor bandpass filter reduces external component count and improves reliability by
minimizing sensitivity to external component values.
G) RFI noise immunity exceeds 30 V/m from 1 MHz to 1000 MHz.
H) High immunity to line frequency noise.
I) Daylight detector circuitry is designed to use either silicon photo diode or CdS detector.
J) Adjustable daylight detector sensitivity.
K) Adjustable OFF timer accuracy is determined by external components.
L) Output can directly drive TRIACs, opto-couplers and small relays (no buffering required).
M) Four main operating modes can be used in any combination:
1)Auto-ON: Load turns on when motion is detected (adjustable sensitivity).
Adjustable daylight detector disables Auto-ON during daytime.
Auto-ON mode can be disabled.
Daylight detector can be disabled.
2)Auto-OFF: Adjustable OFF timer activates whenever motion stops.
Load turns off if there is no motion during the time delay.
If Auto-ON mode is disabled, the load will turn on if there is motion within 6 seconds
after turn-off. (If the load goes off because you stopped moving (reading a book for
example), you have 6 seconds to wave your arm to turn the load back on.)
Auto-OFF mode can be disabled.
3)Manual-ON: Load turns on manually, with a momentary contact switch.
4)Manual-OFF: Load turns off manually, with a momentary contact switch.
mLoad will remain off for 25 seconds, even if there is motion during this time (to give you
otime to leave the room).
.cN) If the ON/AUTO/OFF input is held either high or low, the load will be held ON or OFF respectively,
uoverriding all other modes, until the input returns to the AUTO position.
t4O) If the Toggle input is held low, the load will change from on to off or from off to on, and will be held in
ethat state, overriding all other modes, until the input returns high.
eP) When power is restored after an outage, the load will be OFF and motion will be ignored for 25 seconds.
hQ) Operating chip voltage is 4 - 15V.
tasR) Operating chip current is typically 300 µA.
S) Chip is ESD protected to more than 1000 V (human body model).
aT) Operates with 50-60 Hz AC line frequency.
.d_________________________________________________________________________________________
www KC778B
Rev C, 1996

PagesPages 9
Télécharger [ KC778B ]


Fiche technique recommandé

No Description détaillée Fabricant
KC7783 PIR Sensor Module ETC
ETC
KC7786 PIR Sensor Module ETC
ETC
KC7789 PIR SENSOR WITH BUILT-IN AMPLIFIER ETC
ETC
KC778B Master PIR Control Chip COMedia
COMedia

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche