|
|
PDF TM058WA_22L03 Data sheet ( Hoja de datos )
| Número de pieza | TM058WA_22L03 | |
| Descripción | LCD_Module | |
| Fabricantes | TORiSAN | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TM058WA_22L03 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
www.DataSheeEt4NUG.IcTTNoFME1mT5Ec0CmR5O8IL(N5WO.G8RAinLS-cC2hPD)2EdLMCia0OgI3FoDnIUaClLAETIONS
Resolution (400xR G Bx234 dots)
With CFL backlight unit
mNonglare surface type
t4U.co(TENTATIVE)
eeJuly.23.2001
.DataShTottori SANYO Electric Co., Ltd.
Electronic Device Business Headquarters
w LCD Division
ww 3-201, Minami-yoshikata, Tottori, 680-8634 Japan
TEL: 81-857-21-3414
FAX: 81-857-21-3418
www.DataSheet4U.com
1 page  
OPTICAL CHARACTERISTICS (1)
ITEM
Viewing angle
range
Contrast ratio
Response Rise
time Fall
Color of CIE White
Coordinate
SYMBOL
CONDITIONS
θ= 0°
φ K>=5 θ= 90°
θ=180°
θ=270°
K At optimized viewing angle
tr θ=0°,φ=0°
tf
x θ=0°,φ=0°
y
Ta=25deg C, fV=60Hz
MIN TYP MAX UNIT
NOTE
65 -
-
65 -
- deg. Note 1),4),5)
40 -
-
65 -
-
100 - - - Note 2),4)
- 30 - ms. Note 3),4)
- 20 -
- 0.305 -
Note 4)
- 0.313 -
=180°
View point
DATA
Black
White
Black
=90°
B
100
90
=0°
Note 1) φandθ are defined as above figure.
10
0
tr tf
Note 3) Response time
Note 2) Contrast ratio "K" is defined below formula.
Brightness at ON (White)
Brightness at OFF (Black)
Note 4) Measurement codition
(1) VIN=12.0V, VB,VR,VG = 0.7Vo-p
Follow brightness measurement condition in next item.
Note 5)
θ= 0°
θ= 90°
θ= 180°
θ= 270°
(Down)
(Right)
(Up)
(Left)
Tottori SANYO Electric Co., Ltd.
TM058WA-22L03
Ver.0 Page
3/13
5 Page 
PRECAUTIONS (INSTRUCTIONS FOR SAFE AND PROPER USE)
1.Instructions for safety
(1) Please do not disassemble or modify LCD module to avoid the possibility of
electric shock, damage of electronic components, scratch at display surface or
invasion of foreign particles. In addition, such activity may result in fire
accident due to burning of electronic component.
LCD module disassembled or modified by customer is out of warranty.
(2) Please be careful in handling of LCD module with broken glass.
When the display glass breaks, please pay attention not to injure your finders.
The display surface has the plastic film attached, which prevents dispersion of
glass pieces, however, touching broken edge will injure your fingers.
Also CFL (Cold Cathode Fluorescent Lamp) is made of glass, therefore
please pay attention in the same way.
(3) Please do not touch the fluid flown out of broken display glass.
Should it stick to hand or clothes, wipe off with soap or alcohol immediately
and then wash it with water. Should the fluid get in eyes, wash eyes
immediately with washing lotion for more 15 minutes and then consult the doctor.
(4) CFL contains mercury inside. Please follow regulations or rules by local autonomy
at its disposal.
(5) Before handing LCD module, please switch off the power supply.
2.Instructions for designing
(1) Mounting of LCD
Designing of mounting parts should be adequate so that LCD module is not
putted stresses (ex. Warp or fortion), to achieve good display quality.
(2) Heat radiation
Required CFL generates heat at lighting and causes temperature rise inside
system. Therefore, designing to radiate heat like radiation slits at cabinet is
recommended to meet the specified operating temperature range for LCD module.
(3) Noise on power line
Spike noise contained in power line causes abnormal operation of driving circuit
and abnormal display. To avoid it, spike noise should be suppressed below VDD
+/- 200mVp-p. (In any case, absolute maximum rating should be kept.)
(4) Absolute maximum rating
Absolute maximum rating specified in this specification has to be kept in any
occasion. It shows the maximum that shall not be exceeded.
Exceeding it may cause burning or non-recoverable break of electronic
components in circuit. Please make system design so that absolute maximum
rating is not exceeding even if ambient temperature, input signal and components
are varied.
(5) Protection cover and cut-off filter for ultraviolet rays
When LCD module is used under severe condition like outdoor, it is recommended
to use transparent protection cover over display surface to avoid scratches and
invasion of dust and water. In addition, when LCD module is exposed to direct sun
light for long time, use of cut-off filter for ultraviolet rays is also recommended.
Please be careful not to get condensation.
Tottori SANYO Electric Co., Ltd. TM058WA-22L03 Ver.0
9/13
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet TM058WA_22L03.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TM058WA_22L03 | LCD_Module | TORiSAN |
| TM058WA_22L04 | TFT Color LCD Module | TORiSAN |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |