DataSheetWiki


X4043 fiches techniques PDF

Intersil Corporation - (X4043 / X4045) CPU Supervisor

Numéro de référence X4043
Description (X4043 / X4045) CPU Supervisor
Fabricant Intersil Corporation 
Logo Intersil Corporation 





1 Page

No Preview Available !





X4043 fiche technique
®
Data Sheet
September 30, 2005
X4043, X4045
4k, 512 x 8 Bit
FN8118.1
CPU Supervisor with 4kbit EEPROM
FEATURES
• Selectable watchdog timer
• Low VCC detection and reset assertion
—Five standard reset threshold voltages
—Adjust low VCC reset threshold voltage using
special programming sequence
—Reset signal valid to VCC = 1V
• Low power CMOS
—<20µA max standby current, watchdog on
—<1µA standby current, watchdog OFF
—3mA active current
• 4kbits of EEPROM
—16-byte page write mode
—Self-timed write cycle
—5ms write cycle time (typical)
• Built-in inadvertent write protection
—Power-up/power-down protection circuitry
—Protect 0, 1/4, 1/2, all or 16, 32, 64 or 128 bytes
of EEPROM array with Block Lockprotection
• 400kHz 2-wire interface
• 2.7V to 5.5V power supply operation
www.DataSheet4U.com Available packages
—8 Ld SOIC
—8 Ld MSOP
—8 Ld PDIP
• Pb-free plus anneal available (RoHS compliant)
BLOCK DIAGRAM
DESCRIPTION
The X4043/45 combines four popular functions,
Power-on Reset Control, Watchdog Timer, Supply
Voltage Supervision, and Block Lock Protect Serial
EEPROM Memory in one package. This combination
lowers system cost, reduces board space require-
ments, and increases reliability.
Applying power to the device activates the power-on
reset circuit which holds RESET/RESET active for a
period of time. This allows the power supply and oscilla-
tor to stabilize before the processor can execute code.
The Watchdog Timer provides an independent protec-
tion mechanism for microcontrollers. When the micro-
controller fails to restart a timer within a selectable
time out interval, the device activates the
RESET/RESET signal. The user selects the interval
from three preset values. Once selected, the interval
does not change, even after cycling the power.
The device’s low VCC detection circuitry protects the
user’s system from low voltage conditions, resetting the
system when VCC falls below the minimum VCC trip
point. RESET/RESET is asserted until VCC returns to
proper operating level and stabilizes. Five industry stan-
dard VTRIP thresholds are available, however, Intersil’s
unique circuits allow the threshold to be reprogrammed
to meet custom requirements or to fine-tune the thresh-
old for applications requiring higher precision.
WP
SDA
SCL
VCC
Watchdog Transition
Detector
Data
Register
Command
Decode &
Control
Logic
VCC Threshold
Reset logic
Protect Logic
Status
Register
EEPROM Array
VTRIP
+
-
Watchdog
Timer Reset
Reset &
Watchdog
Timebase
Power-on and
Low Voltage
Reset
Generation
RESET (X4043)
RESET (X4045)
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.

PagesPages 24
Télécharger [ X4043 ]


Fiche technique recommandé

No Description détaillée Fabricant
X40410 (X40410 - X40415) Dual Voltage Monitor Intersil Corporation
Intersil Corporation
X40411 (X40410 - X40415) Dual Voltage Monitor Intersil Corporation
Intersil Corporation
X40414 (X40410 - X40415) Dual Voltage Monitor Intersil Corporation
Intersil Corporation
X40415 (X40410 - X40415) Dual Voltage Monitor Intersil Corporation
Intersil Corporation

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche