X9319 Datasheet PDF - Intersil Corporation
| Part Number | X9319 | |
| Description | Digitally Controlled Potentiometer | |
| Manufacturers | Intersil Corporation | |
| Logo |  |
|
|
There is a preview and X9319 download ( pdf file ) link at the bottom of this page. Total 10 Pages | ||
Preview 1 page No Preview Available !
®
Data Sheet
September 26, 2006
X9319
FN8185.2
Digitally Controlled Potentiometer
(XDCP™)
FEATURES
• Solid-state potentiometer
• 3-wire serial interface
• Terminal voltage, 0 to +10V
• 100 wiper tap points
—Wiper position stored in nonvolatile memory
and recalled on power-up
• 99 resistive elements
—Temperature compensated
—End to end resistance range ±20%
• Low power CMOS
—VCC = 5V
—Active current, 3mA max.
—Standby current, 1mA max.
• High reliability
—Endurance, 100,000 data changes per bit
—Register data retention, 100 years
• RTOTAL value = 10kΩ and 50kΩ
• Packages
—8 Ld SOIC and PDIP
•www.DataSheet4U.com Pb-free plus anneal available (RoHS compliant)
APPLICATIONS
• LCD bias control
• DC bias adjustment
• Gain and offset trim
• Laser diode bias control
• Voltage regulator output control
DESCRIPTION
The Intersil X9319 is a digitally controlled potentiometer
(XDCP). The device consists of a resistor array, wiper
switches, a control section, and nonvolatile memory.
The wiper position is controlled by a 3-wire interface.
The potentiometer is implemented by a resistor array
composed of 99 resistive elements and a wiper switch-
ing network. Between each element and at either end
are tap points accessible to the wiper terminal. The
position of the wiper element is controlled by the CS,
U/D, and INC inputs. The position of the wiper can be
stored in nonvolatile memory and then be recalled
upon a subsequent power-up operation.
The device can be used as a three-terminal potentiometer
for voltage control or as a two-terminal variable resistor for
current control in a wide variety of applications.
PIN CONFIGURATION
PDIP/SOIC
INC
U/D
RH
VSS
18
2 X9319 7
36
45
VCC
CS
RL
RW
BLOCK DIAGRAM
VCC (Supply Voltage)
Up/Down
(U/D)
Increment
(INC)
Device Select
(CS)
Control
and
Memory
VSS (Ground)
General
U/D
INC
CS
RH
RW
RL
VVCSSC
Up/Down
Counter
7-Bit
Nonvolatile
Memory
Store and
Recall
Control
Circuitry
99
98
97
One 96
of
One
Hundred
Decoder
2
1
0
Wiper
Switches
Resistor
Array
Detailed
RH
RL
RW
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
XDCP is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005, 2006. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
|
| |
 
X9319
A.C. OPERATING CHARACTERISTICS
(VCC = 5V ±10%, TA = Full Operating Temperature Range unless otherwise stated)
Limits
Symbol
Parameter
Min.
Typ.(4)
tCl
tlD(5)
tDI(5)
tlL
tlH
tlC
tCPHS
tCPHNS(5)
tIW(5)
tCYC
tR, tF(5)
tPU(5)
tR VCC(5)
CS to INC setup
INC HIGH to U/D change
U/D to INC setup
INC LOW period
INC HIGH period
INC inactive to CS inactive
CS deselect time (STORE)
CS deselect time (NO STORE)
INC to RW change
INC cycle time
INC input rise and fall time
Power-up to wiper stable
VCC power-up rate
100
100
1
1
1
1
20
1
100
4
0.2
Max.
500
500
500
50
Unit
ns
ns
µs
µs
µs
µs
ms
µs
µs
µs
µs
µs
V/ms
POWER-UP AND DOWN REQUIREMENTS
In order to prevent unwanted tap position changes, or an inadvertant store, bring the CS and INC high before or con-
currently with the VCC pin on powerup. The potentiometer voltages must be applied after this sequence is completed.
During power-up, the data sheet parameters for the DCP do not fully apply until 1 millisecond after VCC reaches its
final value. The VCC ramp spec is always in effect.
A.C. TIMING
CS
tCI
INC
U/D
tIW
RW
tCYC
tIL
tIH
tID
tIC
tDI
MI (3)
tCPHS
90% 90%
10%
tCPHNS
tF tR
5 FN8185.2
September 26, 2006
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for X9319 electronic component. |
| Information | Total 10 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ X9319.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| X9312 | The function is E2POT Nonvolatile Digital Potentiometer. Xicor |  |
| X9312 | The function is Terminal Voltage 0V to 15V. Intersil Corporation | |
| X9313 | The function is E2POT Nonvolatile Digital Potentiometer. Xicor | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
X931
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||