DataSheetWiki


HO1301 fiches techniques PDF

RF Monolithics - SAW Oscillator

Numéro de référence HO1301
Description SAW Oscillator
Fabricant RF Monolithics 
Logo RF Monolithics 





1 Page

No Preview Available !





HO1301 fiche technique
• SAW Frequency Stabilization
• Fundamental-Mode Oscillation at 750.0 MHz
• 0.8” x 0.5” x 0.25” Metal Dip Case
This general-purpose oscillator is stabilized by surface-acoustic-wave (SAW) technology. Fundamental oscil-
lation at 750.0 MHz eliminates all internally generated spurious outputs except integral harmonics of 750.0
MHz. The compact size of the rugged, metal, hermetically-sealed case makes this oscillator suitable for a va-
riety of applications.
HO1301
750.0 MHz
SAW
Oscillator
www.DataSheet4U.com
Absolute Maximum Ratings
Rating
DC Supply Voltage
Ambient Temperature
Powered
Storage
Electrical Characteristics
Characteristic
Operating Frequency Absolute Frequency
Tolerance from 750.0 MHz
RF Output Power
Spurious Outputs
Second Harmonics
Third and Higher Harmonics
RF Impedance
Nonharmonic
Nominal Impedance
DC Power Supply
Operating Load VSWR
Operating Voltage
Operating Current
Operating Ambient Temperature
Lid Symbolization (YY=Year, WW=Week)
Value
0 to +13
-40 to +70
-40 to +85
Units
VDC
°C
Dip 14-8 Case
Sym
fO
fO
PO
ZO
GL
VCC
ICC
TA
Notes
1, 7
3, 6
3, 6, 7
3
3, 5
3, 6
3, 6
Minimum
749.750
+7
Typical
750.0
+11
<-80
50
7.9 8.4
30
-20
RFM HO1301 YYWW
Maximum
750.250
±250
+13
-15
-20
-60
1.5:1
8.9
40
+60
Units
MHz
kHz
dBm
dBc
VDC
mA
°C
CAUTION: Electrostatic Sensitive Device. Observe precautions for
handling. COCOM CAUTION: Approval by the U.S. Department of
Commerce is required prior to export of this device.
Notes:
1. One or more of the following United States patents apply: 4,616,197; 4,610,681; and
4,761,616.
2. Unless noted otherwise, all specifications are listed at TA = +25°C ±2°C, VCC = nom-
inal voltage ±0.01 VDC, and load impedance = 50 with VSWR 1.5:1.
3. The design, manufacturing process , and specification of this device are subject to
change without notice.
4. Applies to oscillator only and not to sidebands caused by external electrical or
mechanical sources. (Dedicated external voltage regulation with low-frequency filter-
ing for the DC power supply and proper circuit board layout are recommended for
optimum spectral purity.)
5. For specified maximum operating load VSWR (any angle) at FO. (No instability or
damage will occur for any passive load impedance.)
6. For any combination of VCC and TA within the specified operating ranges.
7. Applies for any combination of Note 5 and 6 conditions.
RF Monolithics, Inc. Phone: (972) 233-2903
Fax: (972) 387-9148
RFM Europe
Phone: 44 1963 251383
Fax: 44 1963 251510
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
BLOCK DIAGRAM
V CC
SAW Oscillator
RF OUTPUT
Buffer Amplifier
ELECTRICAL CONNECTIONS
VCC 1
Case Ground 2
Top
View
CC
13 Case Ground
Case Ground 6
RF Output 7
9 Case Ground
8 VCC
http://www.rfm.com
HO1301-101899
Page 1 of 2

PagesPages 2
Télécharger [ HO1301 ]


Fiche technique recommandé

No Description détaillée Fabricant
HO1300 SAW Oscillator RF Monolithics
RF Monolithics
HO1301 SAW Oscillator RF Monolithics
RF Monolithics

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche