DataSheetWiki


A6281 fiches techniques PDF

Allegro MicroSystems - 3-Channel Constant Current LED Driver

Numéro de référence A6281
Description 3-Channel Constant Current LED Driver
Fabricant Allegro MicroSystems 
Logo Allegro MicroSystems 





1 Page

No Preview Available !





A6281 fiche technique
A6281
3-Channel Constant Current LED Driver
with Programmable PWM Control
Features and Benefits
3 × 10-bit PWM brightness settings
3 × 7-bit dot correction current settings
5 to 17 V operation
Wide output current range, 10 to 150 mA per channel
Internally generated PWM clock
Serial port operates at up to 5 MHz
Data and clock logic architecture allows single
www.DataSheet4Um.ciocmrocontroller control of large quantities of serially-
connected A6281s at fast data transfer rate
Buffered logic outputs to drive cables
Thermal shutdown and UVLO protection
Power-On Reset
Package: 16-terminal QFN (suffix ES)
3 mm x 3 mm footprint
Description
The A6281 is a 3-channel constant current LED driver that
has a wide range of output currents. The A6281 controls LED
brightness with a Pulse Width Modulation (PWM) scheme
that gives the application the capability of displaying a billion
colors in an RGB cluster. The maximum current is set by an
external resistor.
The LED brightness is controlled by performing PWM control
on the outputs. The brightness data of the PWM signal for
each LED is stored in three 10-bit registers. The peak value
for each LED can be adjusted (dot-corrected) to compensate
for mismatch, aging, and temperature effects. All the internal
latched registers are loaded by a 32-bit shift register. One
address bit controls whether dot correction/clock divider ratio
or brightness data is loaded into the registers. The remaining
bits are used for the data.
TheA6281 is designed to minimize the number of components
needed to drive LEDs with large pixel spacing. A large number
of A6281s can be daisy chained together and controlled by
just four control signals (clock, serial data, latch, and output
enable). Each of these inputs is buffered to drive the next chip
in the chain. Also, VIN can be tied to the LED voltage supply
Continued on the next page…
Power Supply Bus
Clock
Data
Latch
Output Enable
Microprocessor
Control Board
Cat5 UTP
Application Diagram
VLED
VIN OutR OutG OutB
Clock In
Clock Out
Data In
Data Out
Latch In
Latch Out
OE In
OE Out
VREG A6281 REXT
Pixel Board #1
Cat5 UTP
VLED
VIN OutR OutG OutB
Clock In
Clock Out
Data In
Data Out
Latch In
Latch Out
OE In
OE Out
VREG A6281 REXT
Pixel Board #2
Cat5 UTP
Pixel Board #N
Figure 1. Functional drawing of daisy chained display application. Additional pixel boards
with A6281 ICs can be applied.
A6281-DS, Rev. 1

PagesPages 11
Télécharger [ A6281 ]


Fiche technique recommandé

No Description détaillée Fabricant
A6280 3-Channel Constant-Current LED Driver Allegro MicroSystems
Allegro MicroSystems
A6281 3-Channel Constant Current LED Driver Allegro MicroSystems
Allegro MicroSystems
A6282 16-Channel Constant-Current LED Driver Allegro MicroSystems
Allegro MicroSystems
A6283 4.6W DUAL AUDIO POWER AMPLIFIER Unisonic Technologies
Unisonic Technologies

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche