DataSheetWiki


ATR0839 fiches techniques PDF

ATMEL Corporation - 4-Channel LVDS Laser Driver for Dual-layer Application

Numéro de référence ATR0839
Description 4-Channel LVDS Laser Driver for Dual-layer Application
Fabricant ATMEL Corporation 
Logo ATMEL Corporation 





1 Page

No Preview Available !





ATR0839 fiche technique
Features
Current-controlled Output Current Source with 4 Input Channels
LVDS Compatible Inputs at Channels 2, 3 and 4 with On-chip 100Termination
Separate Read-channel Enable
Two Selectable Outputs for Grounded Laser Diodes
Output Current per Channel up to 350 mA
Total Output Current up to 600 mA
On-chip RF Oscillator with LVDS Enable
Control of 2 Different Swings and Frequencies by use of 4 External Resistors
Oscillator Frequency Range from 200 MHz to 500 MHz
Maximum Oscillator Current Amplitude 100 mApp
Single 5V Power Supply
Small Pb-free QFN24, 4 mm × 4 mm Package
Applications
Double Layer DVD+/-RW with CD-RW Capability
Recordable Optical Drives
www.DataSheet4U.com
4-Channel LVDS
Laser Driver for
Dual-layer
Application
ATR0839
1. Description
The ATR0839 is a laser diode driver designed to operate two different grounded laser
diodes for DVD-RW/DVD+RW (650 nm) and CD-RW (780 nm). The device includes
four channels for four different optical power levels. The write channels (channels 2
to 4) can be controlled by fast LVDS (Low Voltage Differential Signaling).
The read channel generates a continuous output current, whereas channels 2 to 4 are
designed as write channels with very fast switching speed. All channels are summed
together and routed to one of the two outputs, IOUTA or IOUTB, controlled by the
select input, SELA. Each write channel (channel 2 to 4) can contribute up to 350 mA
to the total output current of up to 600 mA. The read channel can contribute up to
150 mA. Total gains of 100 (read channel) and 250 (channels 2, 3 and 4), are pro-
vided between each reference current input and the selected output. Although the
reference inputs are current inputs, voltage control is possible by using external resis-
tors. An on-chip RF oscillator is available to reduce laser-mode hopping noise during
read mode. The oscillator current amplitude can be set independently for the two
selectable outputs with two different resistors. Oscillation can be enabled either by
LVDS signaling at ENOSC/NENOSC pins, or by a high at ENOSC pin in single-ended
mode. Complete shutdown of the output currents is achieved by a low signal at the
ENABLE input.
In read mode, the reference currents (I2, I3, I4) should be switched off to reduce
power consumption.
In case of uncertain (balanced) enable signals, a built-in fail-safe circuit will reduce the
laser diode output current to a safe value.
Summary
Rev. 4852BS–DVD–09/05
Note: This is a summary document. A complete dorcument
is available under NDA. For more information, please con-
tact your local Atmel sales office.

PagesPages 6
Télécharger [ ATR0839 ]


Fiche technique recommandé

No Description détaillée Fabricant
ATR0839 4-Channel LVDS Laser Driver for Dual-layer Application ATMEL Corporation
ATMEL Corporation

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche