MX23L3254 Datasheet PDF - Macronix International
| Part Number | MX23L3254 | |
| Description | 32M-BIT Low Voltage - Serial Mask ROM Memory with 50MHz SPI Bus Interface | |
| Manufacturers | Macronix International | |
| Logo |  |
|
|
There is a preview and MX23L3254 download ( pdf file ) link at the bottom of this page. Total 18 Pages | ||
Preview 1 page No Preview Available !
FEATURES
• 32Mbit of Mask ROM
• 2.7 to 3.6V Single Supply Voltage
• SPI Bus Compatible Serial Interface
• 50MHz Clock Rate (maximum)
MX23L3254www.DataSheet4U.com
32M-BIT Low Voltage, Serial Mask ROM Memory with
50MHz SPI Bus Interface
DESCRIPTION
The MX23L3254 is a 32Mbit (4M x 8) Serial Mask ROM
accessed by a high speed SPI-compatible bus.
PIN CONFIGURATIONS
16-PIN SOP (300 mil)
HOLD#
VCC
NC
NC
NC
NC
S#
Q
1
2
3
4
5
6
7
8
16 C
15 D
14 NC
13 NC
12 NC
11 NC
10 VSS
9 NC
PIN DESCRIPTION
SYMBOL
C
D
Q
S#
HOLD#
VCC
VSS
DESCRIPTION
Serial Clock
Serial Data Input
Serial Data Output
Chip Select
Hold
Supply Voltage
Ground
Note:
1. NC=No Connection
2. See page 16 (onwards) for package dimensions, and
how to identify pin-1.
ORDER INFORMATION
Part No.
MX23L3254MC-20
MX23L3254MC-20G
MX23L3254MI-20G
Speed
20ns
20ns
20ns
Note:
* Industrial grade operating temperature: -25 ~ 85 ° C
Commercial grade operating temperature: 0 ~ 70 ° C
Package
16-SOP
16-SOP
16-SOP
Remark
Pb-free
Pb-free (Industrial Grade)
P/N: PM1167
REV. 1.2, JUN. 08, 2005
1
|
| |
 
MX23L3254www.DataSheet4U.com
OPERATING FEATURES
Active Power, Stand-by Power
When Chip Select (S#) is Low, the device is enabled, and
in the Active Power mode. When Chip Select (S#) is High,
the device is disabled, but could remain in the Active
Power mode until all internal cycles have completed. The
device then goes in to the Stand-by Power mode. The
device consumption drops to ICC1 .
Protection Modes
The environments where non-volatile memory devices are
used can be very noisy. No SPI device can operate
correctly in the presence of excessive noise. To help
combat this, the MX23L3254 boasts the following data
protection mechanisms:
- Power-On Reset and an internal timer (tPUW) can provide
protection against inadvertant changes while the power
supply is outside the operating specification.
Hold Condition
The Hold (HOLD#) signal is used to pause any serial
communications with the device without resetting the
clocking sequence.
To enter the Hold condition, the device must be selected,
with Chip Select (S#) Low.
The Hold condition starts on the falling edge of the Hold
(HOLD) signal, provided that this coincides with Serial
Clock (C) being Low (as shown in Figure 3).
The Hold condition ends on the rising edge of the Hold
(HOLD#) signal, provided that this coincides with Serial
Clock (C) being Low.
If the falling edge does not coincide with Serial Clock (C)
being Low, the Hold condition starts after Serial Clock (C)
next goes Low. Similarly, if the rising edge does not
coincide with Serial Clock (C) being Low, the Hold condi-
tion ends after Serial Clock (C) next goes Low. (This is
shown in Figure 2).
During the Hold condition, the Serial Data Output (Q) is
high impedance, and Serial Data Input (D) and Serial Clock
(C) are Don't Care.
Normally, the device is kept selected, with Chip Select
(S#) driven Low, for the whole duration of the Hold condi-
tion. This is to ensure that the state of the internal logic
remains unchanged from the moment of entering the Hold
condition.
If Chip Select (S#) goes High while the device is in the Hold
condition, this has the effect of resetting the internal logic
of the device. To restart communication with the device,
it is necessary to drive Hold (HOLD#) High, and then to
drive Chip Select (S#) Low. This prevents the device from
going back to the Hold condition.
Figure 3. Hold Condition Activation (for data output only)
C
HOLD#
Q Q0
Q2
Q1
Q2
Q3
Q4
Q5
C
HOLD#
Q Q0
Q2
Q1
Q2
Q3
Q4
Q5
Q6
P/N: PM1167
REV. 1.2, JUN. 08, 2005
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MX23L3254 electronic component. |
| Information | Total 18 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ MX23L3254.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| MX23L3254 | The function is 32M-BIT Low Voltage - Serial Mask ROM Memory with 50MHz SPI Bus Interface. Macronix International | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
MX23
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||