|
|
PDF ZSE40F Data sheet ( Hoja de datos )
| Número de pieza | ZSE40F | |
| Descripción | Pressure Sensors | |
| Fabricantes | SMC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ZSE40F (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
High Precision,
ZSE40/ISE40Digital Pressure Switch Series
How to Order
Set pressure range
Nil –0.100 to 1.000 MPa For positive pressure
For positive pressure ISE40
For vacuum/compound pressure ZSE40
01 22
01 22
Set pressure range
Nil 10.0 to –101.3 kPa For vacuum pressure
F –100.0 to 100.0 kPa For compound pressure
Piping specifications
01: R 1/8 (With M5 female threads) W1: Rc 1/8
T1: NPT 1/8 (With M5 female threads)
R 1/8, NPT 1/8
Reverse pressure
two directions
Rc 1/8
M5 x 0.8 female threads
Rc 1/8
∗ C4: With ø4 One-touch fitting
∗ C6: With ø6 One-touch fitting
Wall mount
∗ M5: M5 x 0.8 (Female threads)
Wall mount
http://www.DataSheet4U.net/
Option
Nil None
Bracket A
A
(ZS-24-A)
Bracket B
B
(ZS-24-B)
Panel mount (ZS-22-A)
E
ZSE
ISE
PSE
ZI SE3
PS
ZI SE12
ZSP
ISA2
IS
ZSM
PF2
IF
Data
Panel mount (ZS-24-C)
+ Front protective cover
ø4, ø6
One-touch fitting
M5 x 0.8
F
∗ Option
Input/Output specifications
22 NPN open collector 2 outputs + analog output
30 ∗ NPN open collector 2 outputs + auto shift input
62 ∗ PNP open collector 2 outputs + analog output
70 ∗ PNP open collector 2 outputs + auto shift input
∗ Option
Note
When equipped with auto shift function, the following ranges can be set.
Set pressure range
–100.0 to 100.0 kPa
10.0 to –101.3 kPa
–0.1 to 1.000 MPa
Setting range
–100.0 to 100.0 kPa
–101.3 to 101.3 kPa
–1.000 to 1.000 MPa
∗ When optional parts only are
required, order with the part
numbers inside ( ).
Unit specifications
Nil With unit switching function Note1)
M SI unit only Note 2)
Note 1) This will no longer be sold for use in
Japan after the new Weight and
Measure Act is implemented
(October,1999).
Note 2) Fixed unit
For vacuum/compound pressure: kPa
For positive pressure: MPa
Lead wire length
Nil 0.6 m
L 3m
16-2-17
datasheet pdf - http://www.DataSheet4U.net/
1 page  
High Precision,
ZSE40/ISE40Digital Pressure Switch Series
Unit Set
It's only subject to ZSE40(F)/ISE40--(L).
Output Type
ON
Unit selection
[P]
≥
Set the unit by either į button or Ĭ button.
: kPa or MPa, : kgf/cm2,
: bar,
: psi,
: inHg,
: mmHg
OUT1
Output mode
∗ OUT2: Same as OUT1.
SET Press “SET” button.
OUT1: Selection of the output mode
≥
[N]
YES
NO
OFF
P-2 P-1
High pressure (for positive pressure/compound pressure)
High vacuum (for vacuum pressure)
Ǟ
Ȝ Hysteresis mode
H
ON
H H (Fixed hysteresis) = 3 digits
OFF P-1
P-2
High pressure (for positive pressure/compound pressure)
ǞHigh vacuum (for vacuum pressure)
Ȝ Window comparator mode
ZSE
ISE
PSE
ZI SE3
YES
NO
ON PS
OFF
n-2 n-1
High pressure (for positive pressure/compound pressure)
ǞHigh vacuum (for vacuum pressure)
Ȝ Hysteresis mode
H
ON
H H (Fixed hysteresis) = 3 digits
OFF n-1
n-2
High pressure (for positive pressure/compound pressure)
ǞHigh vacuum (for vacuum pressure)
Ȝ Window comparator mode
ZI SE12
ZSP
ISA2
IS
ZSM
Auto Preset (For adsorption confirmation)
1. Auto preset mode
2. Preparation for auto preset
3. Auto preset of OUT1
PF2
IF
http://www.DataSheet4U.net/
SET
Press the “SET” button.
Data
Select the Auto preset mode in
the initial setting mode and
press the “SET” button until
“ ” is displayed.
Prepare the equipment for use
under operating conditions.
When setting OUT1 is not
required, press both the į
button and Ĭ button
simultaneously in this state to
skip to “ ”.
4. Preparation for auto preset
Repeat adsorption and non-
adsorption release several times
in this state.
The optimal set value is
determined automatically.
5. Auto preset of OUT2
High
Vacuum
Max. A
ON
Suction
Workpiece 1
Workpiece 2
Workpiece n
OFF
Min. B
Released
Workpiece 1
Workpiece 2
Workpiece n
Atmosphere
Max. A: Max. pressure value when a workpiece is adsorbed.
ON =
A
–
A–
4
B
Min. B: Min. pressure value when a workpiece is not adsorbed.
OFF
=
B
+
A
–
4
B
SET
Press the “SET” button.
SET
Press the “SET” button.
SET
Press the “SET” button
to complete the setting.
Supplies vacuum pressure,
changing the condition of a
workpiece by adsorption nozzle,
etc. When setting OUT2 is not
required, press both the į
button and Ĭ button
simultaneously in this state to
skip to the measurement mode.
Repeat adsorption and non-
adsorption several times in this
state.
The optimum set value is
determined automatically.
16-2-21
datasheet pdf - http://www.DataSheet4U.net/
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet ZSE40F.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ZSE40 | Pressure Sensors | SMC |
| ZSE40F | Pressure Sensors | SMC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |