UBA2071 Datasheet PDF - NXP Semiconductors
| Part Number | UBA2071 | |
| Description | Half bridge control IC | |
| Manufacturers | NXP Semiconductors | |
| Logo |  |
|
|
There is a preview and UBA2071 download ( pdf file ) link at the bottom of this page. Total 35 Pages | ||
Preview 1 page No Preview Available !
UBA2071; UBA2071A
Half bridge control IC for CCFL backlighting
Rev. 01 — 23 June 2008
Product data sheet
1. General description
2. Features
The UBA2071 and UBA2071A are high voltage ICs intended to drive Cold Cathode
Fluorescent Lamps (CCFLs) or External Electrode Fluorescent Lamps (EEFLs) for
backlighting applications. They can drive a half bridge circuit made up of two NMOSFETs
with a supply voltage of up to 550 V, so the inverter can be supplied directly from a 400 V
PFC bus.
The UBA2071 and UBA2071A contain a controller, a level shifter, a bootstrap diode and
drivers for the external half bridge power switches. It also contains a low frequency PWM
generator, which can be used to control the brightness level of the lamps, using an analog
brightness/dimming control voltage. PWM dimming can also be realized, using a digital
PWM input signal. PWM dimming can be synchronized with other ICs. The lamp current is
controlled by means of a true zero voltage switching resonant control principle, ensuring
lowest possible switch losses in the half bridge power structure.
The UBA2071 is designed to be supplied by a ∆V/∆t supply from the half bridge circuit that
it drives. The IC itself needs little current and if the IC is off, a clamp protects the supply
voltage from getting too high.
The UBA2071A is designed to be supplied by a fixed 12 V supply. It has a lower supply
start voltage and no supply clamp.
http://www.DataSheet4U.net/
I Suitable for operating in a very wide inverter supply voltage range (up to 550 V DC).
I Integrated level shifter.
I Integrated bootstrap diode.
I Lamp current control by means of a true zero voltage switching resonant control
principle.
I Sample & Hold circuit, maintaining current control value during PWM lamp-off
situation.
I Separately definable time constants for current control loop and PWM dimming
attack/decay setting.
I Overvoltage control.
I Overcurrent protection.
I Ignition failure detection.
I Hard switching control.
I Arcing detection.
I Open/short pin protections on feedback pins.
I Integrated, programmable fault timer.
datasheet pdf - http://www.DataSheet4U.net/
|
| |
 
NXP Semiconductors
7. Pinning information
7.1 Pinning
UBA2071; UBA2071A
Half bridge control IC for CCFL backlighting
IFB 1
CIFB 2
VFB 3
CVFB 4
CSWP 5
CT 6
CF 7
IREF 8
CPWM 9
SGND 10
COMM 11
NONFAULT 12
UBA2071
24 GH
23 FS
22 SH
21 n.c.
20 n.c.
19 n.c.
18 GL
17 PGND
16 VDD
15 EN
14 PWMA
13 PWMD
014aaa099
Fig 2. Pin assignment SO24 and SSOP24 package (top view)
7.2 Pin description
Table 3.
Symbol
IFB
CIFB
VFB
CVFB
CSWP
CT
CF
IREF
CPWM
SGND
COMM
Pin description
Pin Description
Function
http://www.DataSheet4U.net/
1 current feedback input. Input signal for the lamp current control loop. Should be connected to a
voltage proportional to the lamp current.
2 current regulation
capacitor.
A capacitor must be connected between this pin and the signal ground. It
sets the time constant of the lamp current control loop.
3 voltage feedback input Input signal for the voltage control loop. Should be connected to a voltage
proportional to the transformer output voltage.
4 voltage regulation
capacitor
A capacitor must be connected between this pin and the signal ground. It
sets the time constant of the voltage control loop.
5 frequency sweep
capacitor
A capacitor must be connected between this pin and the signal ground. It
sets the time in which the HF frequency is swept up from regulation level to
the maximum frequency and back during PWM dimming.
6 fault timing capacitor
A capacitor must be connected between this pin and the signal ground. It
sets the time that a fault condition is allowed before the IC shuts down itself.
7 HF-oscillator timing
capacitor
A capacitor must be connected between this pin and the signal ground. It
sets the minimum switching frequency of the half bridge.
8 reference current output A 33 kΩ resistor must be connected between this pin and the signal ground.
The IC uses it to make accurate internal currents.
9 PWM timing capacitor If a capacitor is connected between this pin and the signal ground, it sets the
frequency of the PWM oscillator.
If this pin is connected to signal ground the internal PWM oscillator is
disabled.
10 signal ground
11 master / slave
communication
Via this pin the IC can communicate with a dedicated slave device.
UBA2071_A_1
Product data sheet
Rev. 01 — 23 June 2008
© NXP B.V. 2008. All rights reserved.
5 of 35
datasheet pdf - http://www.DataSheet4U.net/
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for UBA2071 electronic component. |
| Information | Total 35 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ UBA2071.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| UBA2070 | The function is CCFL ballast driver IC. NXP Semiconductors | |
| UBA2071 | The function is Half bridge control IC. NXP Semiconductors | |
| UBA2071A | The function is Half bridge control IC. NXP Semiconductors | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
UBA2
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||