|
|
Número de pieza | 15-23B-R6G6BHC-A01-2T | |
Descripción | Full Color Chip LEDs | |
Fabricantes | Everlight | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de 15-23B-R6G6BHC-A01-2T (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
No Preview Available ! EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet
Full Color Chip LEDs
15-23B/R6G6BHC-A01/2T
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Full-color type.
Descriptions
․The 15-23B SMD Taping is m uch smaller
than lead fram e type com ponents, thus
enable sm aller board size, higher packing
density, reduced storage space and finally
smaller equipment to be obtained.
․Besides, lightweight m akes them ideal for
miniature applications. etc.
Applications
․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Chip
Type Material
Emitted Color
R6 AlGaInP
Brilliant Red
G6
InGaN
Brilliant Yellow Green
BH InGaN
Blue
Lens Color
Water Clear
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:DSE-153-
Prepared
date: 09-08-2003
Rev 1.0 Page:
Prepared by: Jeff Tsai
1 of 12
http://www.Datasheet4U.com/
1 page EVERLIGHT ELECTRONICS CO.,LTD.
15-23B/R6G6BHC-A01/2T
Typical Electro-Optical Characteristics Curves
R6
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:DSE-153-
Prepared
date: 09-08-2003
Rev 1.0 Page:
Prepared by: Jeff Tsai
5 of 12
http://www.Datasheet4U.com/
5 Page EVERLIGHT ELECTRONICS CO.,LTD.
15-23B/R6G6BHC-A01/2T
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Lead solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No:DSE-153-
Prepared
date: 09-08-2003
Rev 1.0 Page:
Prepared by: Jeff Tsai
11 of 12
http://www.Datasheet4U.com/
11 Page |
Páginas | Total 12 Páginas | |
PDF Descargar | [ Datasheet 15-23B-R6G6BHC-A01-2T.PDF ] |
Número de pieza | Descripción | Fabricantes |
15-23B-R6G6BHC-A01-2T | Full Color Chip LEDs | Everlight |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |