|
|
PDF GP-MF802 Data sheet ( Hoja de datos )
| Número de pieza | GP-MF802 | |
| Descripción | Industrial Camera Service Manual | |
| Fabricantes | Panasonic | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de GP-MF802 (archivo pdf) en la parte inferior de esta página. Total 21 Páginas | ||
|
No Preview Available !
ORDER NO. AVS9705028C1
D0
Industrial Camera
GP-MF802
Camera Cable : Option
Lens :
Option
SPECIFICATIONS
Pick-up Device :
Image Size :
Synchronization :
External Reset :
Horizontal Resolution :
Minimum Illumination :
Signal to Noise Ratio :
Electronic Shutter :
Lens Mount :
Vibration Resistance :
Shock Resistance :
Power Source :
Ambient Temperature :
Progressive Scanning Interline Transfer CCD with 659 (H) x 494 (V) pixels.
1/3” (6.3 (H) x 6.4 (V) mm)
2 : 1 interlace 1-line interlace (Frame accumulation)
2 : 1 interlace 2-line interlace (Field accumulation)
2-line sequential (at non-interlaced external HD/VD)
internal or external (Selectable automatically)
Internal : Built-in sync generator
External : 4.0 V[p-p] / 75 Ω Horizontal drive and vertical drive pulses for 2 : 1 interlace or sequential
scanning
External signal (4.0 V[p-p]/75 Ω, negative) supplied to EXT VD IN connector can be used as reset sig -
nal
480 lines at center
6.5 lx (0.65 footcandles ) at F1.4, (Manual Gain Max, γ ON, 2 : 1 interlace, without shutter)
56 dB Typical (Fix Gain, γ OFF, 2:1 interlace without shutter)
7-step (1/100 to 1/8,000) at normal.
4-step (1/2,000 to 1/16,000) at Shutter Trigger-A.
Approx. 1/2,000 at Shutter Trigger-B.
C-mount
8 G (10 Hz - 150 Hz), (2 hours each for three axes)(IEC 68)
80 G (IEC 68) *IEC=International Electrotechnical Commission
12V DC, 190 mA
−10˚C - +50˚C (14˚F - 122˚F)
C1997 Matsushita Communication Industrial Co., Ltd.
All rights reserved. Unauthorized copying and
R distribution is a violation of law.
http://www.Datasheet4U.com
1 page  
6. Switch 3 (3/ON) 3
ON
This switch is used to set the frame reset (shutter trig -
ger) to on or off.
In case of frame reset off, you can select a shutter speed
using switch 4, switch 5, and switch 6.
Shutter speeds and combinations of the switches in case
of frame reset off are shown in the table below;
Switch
Shutter Speed
654
OFF OFF OFF NORMAL
ON OFF OFF 1/100
OFF ON OFF 1/250
ON ON OFF 1/500
OFF OFF ON 1/1000
ON OFF ON 1/2000
OFF ON ON 1/4000
ON ON ON 1/8000
In case of frame reset on, you can select a shutter speed
or long time exposure mode using switch 4, switch 5,
and switch 6.
Shutter speeds and combinations of the switches in case
of frame reset on are shown in the table below;
Switch
Shutter Speed
654
OFF OFF OFF
ON OFF OFF The long time
OFF ON OFF exposure mode
ON ON OFF
OFF OFF ON 1/2000
ON OFF ON 1/4000
OFF ON ON 1/8000
ON ON ON 1/16000
Note: The accurate shutter speed function cannot be
expected in non-interlaced synchronization.
7. Switch 4 (4/ON) 4
ON
Set this switch with switch 5 and switch 6 as shown in
the tables above.
8. Switch 5 (5/ON) 5
ON
Set this switch with switch 4 and switch 6 as shown in
the tables above.
9. Switch 6 (6/ON) 6
ON
Set this switch with switch 4 and switch 5 as shown in
the tables above.
10. Switch 7 (7/ON) 7
ON
Set this switch to ON to terminate the external HD sig-
nals with 75Ω.
11. Switch 8 (8/ON) 8
ON
Set this switch to ON to terminate the external VD sig
nals with 75Ω.
-
12. Switch 9 (9/ON) 9
ON
This switch is used to set long time exposure mode to
ON or OFF.
Set this switch to ON only when switch 3 is set to ON
with switches 4, 5 and 6 in the specified positions.
This switch changes the AC/DC coupling to AC coupling
when OFF is selected or to DC coupling when ON is
selected.
13. Switch 10 (10/ON) 10
ON
This switch is used to set the clock out function to ON or
OFF.
2
5 Page 
2.2. IC7 on the Power Board is using the Switching Regulator Controller IC YWMB3775PFV.
Description of this IC is as follows:
CT 1
RT 2
+IN1 3
–IN1 4
FB1 5
DTC1 6
OUT1 7
GND 8
(TOP VIEW)
16 REF
15 SCP
14 +IN2
13 –IN2
12 FB2
11 DTC2
10 OUT2
9 Vcc
Pin Name I/O
Description
1 CT
– Timing capacitor connecting terminal.
2 RT
3 +IN1
– Timing resistor connecting terminal.
I Non-inverted signal input terminal for
Error Amplifier 1.
4 –IN1
I Inverted signal input terminal for Error
Amplifier 1.
5 FB1
– Feedback terminal for Error Amplifier 1.
6 DTC1 I Dead Time Control signal input terminal.
7 OUT1 O Control signal output terminal 1.
8 GND
9 Vcc
– Ground terminal.
– Power supply terminal.
10 OUT2 O Control signal output terminal 2.
11 DTC2 I Dead Time Control signal input terminal.
12 FB2
13 –IN2
14 +IN2
– Feedback terminal for Error Amplifier 2.
I Inverted signal input terminal for Error
Amplifier 2.
I Non-inverted signal input terminal for
Error Amplifier 2.
15 SCP
– Short Circuit Protection terminal.
16 REF
O Reference voltage output terminal.
Vcc 9
Vref=1.28V
REF 16
Reference Voltage
Source
2.5V
1.9V
1.3V
+IN1 3
–IN1 4
Error Amp. 1
+
–
FB1 5
S.C.P. Comparator
+
+
–
1.1V
FB2 12
+IN2 14
–IN2 13
SCP 15
+
–
Error Amp. 2
2.5V
SR
Latch
R
U.V.L.O.
CT 1 RT 2
Triangular
Wave Generator
+
–
–
PWM Comparator 1
+
–
–
OUT 1
PWM Comparator 2
OUT 2
1.28V
8 GND
+
+
–
D.T.C. Comparator
DTC1 61
1 DTC2
7 OUT1
10 OUT2
8
11 Page | ||
| Páginas | Total 21 Páginas | |
| PDF Descargar | [ Datasheet GP-MF802.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| GP-MF802 | Industrial Camera Service Manual | Panasonic |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |