|
|
PDF SS19 Data sheet ( Hoja de datos )
| Número de pieza | SS19 | |
| Descripción | Analog Position Sensors | |
| Fabricantes | Honeywell | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SS19 (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
|
No Preview Available !
Installation Instructions for the
SS49/SS19 Series Analog Position Sensors
ISSUE 2
PK 88740
PERSONAL INJURY
• DO NOT USE these products as safety or
emergency stop devices, or in any other
application where failure of the product could
result in personal injury.
Failure to comply with these instructions could
result in death or serious injury.
SS49/SS19 ELECTRICAL CHARACTERISTICS
Supply Voltage
4 to 10 VDC
Supply Current
4 mA typ.
Output Type
Analog Sourcing
Output Voltage @ 0
Gauss, 25°C
1.75 to 2.25 V @ 5 V
Sensitivity (measured Min. Typ. Max.
between -400 and +400 0.60 0.90 1.25
gauss), mV/G
Operating Temperature -40 to +100°C (-40 to 212°F)
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (Vs)
± 12 VDC
Output Current
20 mA
Storage Temperature
-55 to +150°C (-67 to
+302°F)
Magnetic Flux
No limit. Circuit cannot be
damaged by magnetic
overdrive.
Absolute maximum ratings are the extreme limits
the device will withstand without damage to the
device. However, the electrical and mechanical
characteristics are not guaranteed as the maximum
limits (above recommended operating conditions)
are approached, nor will the device necessarily
operate at absolute maximum ratings.
SOLDERING/ASSEMBLY
SS49
Support leads during any forming/shearing
operation. Do not stress leads inside plastic case.
Hand soldering - Use 60/40 rosin core solder,
and a 399°C (750°F) controlled temperature, 1/8”
chisel tip soldering iron. Do not hold iron on
terminals for more than four seconds. Lead
temperature at package must not exceed 250°C
(482°F).
Wave soldering - Use Loncoflux 106A35 or
equivalent. Set preheaters at 95°C (200°F) for top
(component side) of PC board just prior to entering
wave. (This may be adjusted depending upon
board thickness.) Set solder temperature at 252°C
to 260°C max. (485°F to 500°F). Set conveyor
speed to about 4.5 feet per minute (1,37
meter/min.), choosing a speed which gives full
solder fillets and minimum bridging and icicles.
Provide rigid support for the board.
SS19/SS19T
MICRO SWITCH recommends an infrared reflow
process with peak temperatures not to exceed 190 -
200°C (374 - 392°F) for 10 seconds maximum.
Keep exposure to high temperatures minimal.
CLEANING
Clean appropriately in accordance with applicable
safety procedures. MICRO SWITCH recommends
manual cleaning.
BLOCK DIAGRAM
TRANSFER CHARACTERISTICS
MICRO SWITCH Sensing and Control
1 page | ||
| Páginas | Total 4 Páginas | |
| PDF Descargar | [ Datasheet SS19.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SS100 | (SS12 - SS100) 1.0 Ampere Schottky Barrier Rectifiers |  Fairchild Semiconductor |
| SS100 | (SS12 - SS100) SURFACE MOUNT SCHOTTKY BARRIER RECTIFIERS |  Jinan Gude Electronic Device |
| SS100 | (SS12 - SS100) SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER |  TRSYS |
| SS100 | Surface Mount Digital Position Sensors |  HONEYWELL |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |