HC-5502B1 Datasheet PDF - Intersil Corporation
| Part Number | HC-5502B1 | |
| Description | SLIC Subscriber Line Interface Circuit | |
| Manufacturers | Intersil Corporation | |
| Logo |  |
|
|
There is a preview and HC-5502B1 download ( pdf file ) link at the bottom of this page. Total 12 Pages | ||
Preview 1 page No Preview Available !
TM POSSDOIaBBtLaSEOSShLUEHeBeTCStE-5TP5ITR0U2OBTDEUPCRTODUCT
HC-5502B1
April 1999 File Number 4127.2
SLIC Subscriber Line Interface Circuit
Features
[ /Title
(HC-
5502B
1)
/Sub-
ject
(SLIC
Sub-
scriber
Line
Inter-
face
Cir-
cuit)
/Autho
r ()
/Key-
words
(Inter-
sil
Semi-
con-
ductor,
RSLIC
18,
Tele-
com,
SLICs,
SLACs
, Tele-
phone,
Tele-
phony,
WLL,
Wire-
less
Local
Loop,
PBX,
Pri-
vate
Branch
Exchan
ge,
The Intersil SLIC incorporates many of the BORSHT
function on a single IC chip. This includes DC battery feed, a
ring relay driver, supervisory and hybrid functions. This
device is designed to maintain transmission performance in
the presence of externally induced longitudinal currents.
Using the unique Intersil dielectric isolation process, the
SLIC can operate directly with a wide range of station
battery voltages.
The SLIC also provides selective denial of power. If the PBX
system becomes overloaded during an emergency, the SLIC
will provide system protection by denying power to selected
subscriber loops.
The Intersil SLIC is ideally suited for the design of new digital
PBX systems, by eliminating bulky hybrid transformers.
Ordering Information
TEMP. RANGE
PART NUMBER
(oC)
PACKAGE
HC3-5502B1-5
HC4P5502B1-5
HC9P5502B1-5
0 to 75
0 to 75
0 to 75
24 Ld PDIP
28 Ld PLCC
24 Ld SOIC
PKG.
NO.
E24.6
N28.45
M24.3
Pinouts
HC-5502B1 (PDIP, SOIC)
TOP VIEW
TIP 1
RING 2
VB+ 3
C1 (NOTE) 4
C3 5
DG 6
RS 7
RD 8
TF 9
RF 10
VB- 11
BG 12
24 TX
23 AG
22 C4
21 RX
20 +IN
19 -IN
18 OUT
17 C2
16 RC
15 PD
14 GKD
13 SHD
NOTE: Optional.
• Low Cost Version of HC-5502B
• Capable of 12V or 5V (VB+) Operation
• Monolithic Integrated Device
• DI High Voltage Process
• Compatible With Worldwide PBX Performance
Requirements
• Controlled Supply of Battery Feed Current for Short Loops
(30mA)
• Internal Ring Relay Driver
• Low Power Consumption During Standby
• Switch Hook, Ground Key and Ring Trip Detection
Functions
• Selective Denial of Power to Subscriber Loops
Applications
• Solid State Line Interface Circuit for Analog and Digital PBX
Systems
• Direct Inward Dial (DID) Trunks
• Voice Messaging PBXs
• Related Literature
- AN549, The HC-5502S/4X Telephone Subscriber Line
Interface Circuits (SLIC)
- AN571, Using Ring Sync with HC-5502A and HC-5504
SLICs
HC-5502B1 (PLCC)
TOP VIEW
4 3 2 1 28 27 26
C1 (NOTE) 5
C3 6
DG 7
N/C 8
RS 9
RD 10
TF 11
25 RX
24 +IN
23 -IN
22 N/C
21 OUT
20 C2
19 RC
12 13 14 15 16 17 18
4-1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-724-7143| Copyright © Intersil Corporation 1999
|
| |
 
HC-5502B1
Pin Descriptions
28 PIN
PLCC
2
3
4
5
6
7
9
10
11
12
13
14
16
17
18
19
20
21
23
24
25
24 PIN
DIP/SOIC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
SYMBOL
DESCRIPTION
TIP An analog input connected to the TIP (more positive) side of the subscriber loop through a 150Ω feed
resistor and a ring relay contact. Functions with the Ring terminal to receive voice signals from the tele-
phone and for loop monitoring process.
RING
An analog input connected to the RING (more negative) side of the subscriber loop through a 150Ω feed
resistor and a ring relay contact. Functions with the Tip terminal to receive voice signals from the tele-
phone and for loop monitoring purposes.
VB+ Positive Voltage Source - Most positive supply. VB+ is typically 12V or 5V.
C1 Capacitor #1 - Optional Capacitor used to improve power supply rejection. This pin should be left open if un-
used.
C3 Capacitor #3 - An external capacitor to be connected between this terminal and analog ground. Required
for proper operation of the loop current limiting function, and for filtering VB- supply. Typical value is 0.3µF,
30V.
DG Digital Ground - To be connected to zero potential and serves as a reference for all digital inputs and out-
puts on the SLIC.
RS Ring Synchronization Input - A TTL - Compatible Clock Input. The clock should be arranged such that a
positive transition occurs on the negative going zero crossing of the ring voltage source, ensuring that the
ring relay is activated and deactivated when the instantaneous ring voltage is near zero. If synchronization
is not required, tie to 5V.
RD Relay Driver - A low active open collector logic output. When enabled, the external ring relay is energized.
TF Tip Feed - A low impedance analog output connected to the TIP terminal through a 150Ω feed resistor.
Functions with the RF terminal to provide loop current, feed voice signals to the telephone set, and sink
longitudinal current.
RF Ring Feed - A low impedance analog output connected to the RING terminal through a 150Ω feed resistor.
Functions with the TF terminal to provide loop current, feed voice signal to the telephone set, and sink
longitudinal current.
VB- Negative Voltage Source - Most negative supply. VB- is typically -48V with an operational range of -42V
to -58V. Frequently referred to as “battery”.
BG Battery Ground - To be connected to zero potential. All loop current and some quiescent current flows into
this ground terminal.
SHD
Switch Hook Detection - A Low Active LS TTL - Compatible Logic Output. This output is enabled for loop
currents exceeding 10mA and disabled for loop currents less than 5mA.
GKD
Ground Key Detection - A Low Active LS TTL - Compatible Logic Output. This output is enabled if the DC
current into the ring lead exceeds the DC current out of the tip lead by more than 20mA, and disabled if
this current difference is less than 10mA.
PD Power Denial - A Low Active TTL - Compatible Logic Input. When enabled the switch hook detect (SHD)
and ground key detect (GKD) are not necessarily valid, and the relay driver (RD) output is disabled.
RC Ring Command - A Low Active TTL - Compatible Logic Input. When enabled, the relay driver (RD) output
goes low on the next rising edge of the ring sync (RS) input, as long as the SLIC is not in the power denial
state (PD = 0) or the subscriber is not already off- hook (SHD = 0).
C2 Capacitor #2 - An external capacitor to be connected between this terminal and digital ground. Prevents
false ground key indications from occurring during ring trip detection. Typical value is 0.15µF, 10V. This
capacitor is not used if ground key function is not required.
OUT The analog output of the spare operational amplifier.
-IN The inverting analog input of the spare operational amplifier.
+IN The non-inverting analog input of the spare operational amplifier.
RX Receive Input, Four Wire Side - A high impedance analog input which is internally biased. Capacitive cou-
pling to this input is required. AC signals appearing at this input differentially drive the Tip feed and Ring
feed amplifiers, which in turn drive tip and ring through 300Ω of feed resistance on each side of the line.
4-5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for HC-5502B1 electronic component. |
| Information | Total 12 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ HC-5502B1.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| HC-5502B | The function is EIA/ITU PABX SLIC with 30mA Loop Feed. Intersil Corporation | |
| HC-5502B1 | The function is SLIC Subscriber Line Interface Circuit. Intersil Corporation | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
HC-5
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||