|
|
PDF T315XW01VF Data sheet ( Hoja de datos )
| Número de pieza | T315XW01VF | |
| Descripción | WXGA Color TFT-LCD Module | |
| Fabricantes | AUO | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de T315XW01VF (archivo pdf) en la parte inferior de esta página. Total 22 Páginas | ||
|
No Preview Available !
Global LCD Panel Exchange Center
www.panelook.com
T315XW01 VF (QD32HL02)
2/23
Document Version : 02
Date : 2006/11/20
Product Specifications
31.5” WXGA Color TFT-LCD Module
Model Name: T315XW01 VF
(QD32HL02)
( ) Preliminary Specifications
(*) Final Specifications
©Copyright AU Optronics, Inc.
January, 2006 All Rights Reserved. T315XW01 VF - Specs. Ver 02
No Reproduction and Redistribution Allowed
2/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
1 page  
Global LCD Panel Exchange Center
www.panelook.com
T315XW01 VF (QD32HL03)
6/23
1. Application
This specification applies to a color TFT-LCD module QD32HL02.
2. Overview
This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is
composed of a color TFT-LCD panel; driver ICs, control circuit and power supply circuit and a backlight unit. Graphics
and texts can be displayed on a 1366 3 768 dots, Wide XGA mode, with 16,777,216 colors by using 8-bit 1 channel
LVDS (Low Voltage Differential Signaling) to interface and +12V DC supply voltage for TFT-LCD panel driving.
The TFT-LCD panel used for this module has wide view angles and fast response time. Display mode is normally
black. Each pixel is divided into Red, Green and Blue sub-pixels, which are arranged in vertical strips. A low-reflection
surface treatment and high-color-saturation type color filter are also used for this panel. Therefore, this module is
suitable for the multimedia use. Especially TV can be obtained by using this module.
[Features]
1) High contrast image. (800:1)
2) High brilliant image. (500 nits)
3) Wide viewing angle. (88/88/88/88)
4) Fast response time. (21ms)
5) High color saturation. (NTSC 72%)
6) WXGA resolution. (1366x768)
7) LVDS interface. (8-bit 1 channel)
3. General Specification
Parameter
Display size
Active area
Pixel format
Pixel size
Pixel configuration
Color depth
Luminance (Center point typ.)
Contrast Ratio
View angle
Display mode
Unit outline dimensions (typ.)*1
Weight (Max.)
Surface treatment
Lamp Quantity
*1.Note : excluding backlight cables.
Specifications
80.04 (31.5") Diagonal
697.685 (H) 392.256 (V)
1366 (H) 768 (V) ; (1 pixel = R+G+B dots)
0.5107 (H) × 0.5107 (V)
R, G, B vertical stripe
16.7M colors
500
1000:1
88/88/88/88
Normally Black
760.0 450.0 48.0
6000
Anti-glare and hard-coating 3H
Direct 16 Lamps
Unit
mm
mm
Pixel
mm
Cd/m2
mm
g
pcs
©Copyright AU Optronics, Inc.
January, 2006 All Rights Reserved. T315XW01 VF - Specs. Ver 02
No Reproduction and Redistribution Allowed
6/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
5 Page 
Global LCD Panel Exchange Center
www.panelook.com
T315XW01 VF (QD32HL03)
12/23
Note.1 Luminance ratio is linearly controllable in the range of the following table.
BTRI Voltage (VBI)
Luminance ratio
0V 20% (Minimum)
3.3V
100% (Maximum)
(1) ADIM is control signal for Inverter’s output Power to Back Light Lamp Bulb. Input Signal should be able to control
Amplitude of Inverter Output voltage. From 0V to 3.3V, Inverter Output Voltage should be able to vary to control
Brightness of Lamp from 80% to 120% Luminescence variation.
(2) PDIM is PWM control input; i.e. for the given ADIM, this PDIM input should be able to control Width of Voltage
Burst of inverter output for Lamp Driving. This input can have two type of input; Ordinary default setting is Duty
Signal Input with 3.3V TTL specification. The other setting will be DC level signal using Saw Tooth Wave control
for PWM duty control. These two method should be decided by 14th Pin input setting.
(3) 14 Pin is selection pin for PWM control method; if this pin NC or GND, PDIM input of 13 th Pin should be direct Duty
Signal Input for PWM control. If this is set to High, 13th Pin should have DC level signal and inverter should have
Saw Tooth Wave Generator for PWM.
Rear view of LCM
PC
14
1
S14B-PH-SM3-TB(JST)
©Copyright AU Optronics, Inc.
January, 2006 All Rights Reserved. T315XW01 VF - Specs. Ver 02
No Reproduction and Redistribution Allowed
12/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
11 Page | ||
| Páginas | Total 22 Páginas | |
| PDF Descargar | [ Datasheet T315XW01VF.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| T315XW01V0 | COLOR TFT LCD MODULE |  AU_OPTRONICS |
| T315XW01V2 | LCD Module | AUO |
| T315XW01V5 | LCD Module | AUO |
| T315XW01V5A | TFT LCD Module | AUO |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |