ACPL-P314 Datasheet PDF - Avago Technologies
| Part Number | ACPL-P314 | |
| Description | 0.6 Amp Output Current IGBT Gate Driver Optocoupler | |
| Manufacturers | Avago Technologies | |
| Logo |  |
|
|
There is a preview and ACPL-P314 download ( pdf file ) link at the bottom of this page. Total 13 Pages | ||
Preview 1 page No Preview Available !
ACPL-P314 and ACPL-W314
0.6 Amp Output Current IGBT Gate Driver Optocoupler
Data Sheet
Description
The ACPL-P314/W314 consists of a GaAsP LED optically
coupled to an integrated circuit with a power output
stage. These optocouplers are ideally suited for driving
power IGBTs and MOSFETs used in motor control
inverter applications. The high operating voltage range
of the output stage provides the drive voltages
required by gate controlled devices. The voltage and
current supplied by this optocoupler makes it ideally
suited for directly driving small or medium power
IGBTs.
Functional Diagram
ANODE 1
N.C. 2
CATHODE 3
SHIELD
6 VCC
5 VO
4 VEE
Truth Table
LED VO
OFF LOW
ON HIGH
Note: A 0.1 µF bypass capacitor
must be connected between
pins VCC and VEE.
Features
• High speed response.
• Ultra high CMR.
• Bootstrappable supply current.
• Available in Stretched SO-6 package
• Package Clearance/Creepage at 8mm (ACPL-W314)
• Safety Approval:
UL Recognized with 3750 Vrms for 1 minute per
UL1577.
CSA Approved.
IEC/EN/DIN EN 60747-5-2 Approved with VIORM =
630VPEAK for option 060.
Specifications
• 0.6 A maximum peak output current.
• 0.4 A minimum peak output current.
• 0.7 µs maximum propagation delay over
temperature range.
• ICC(max) = 3 mA maximum supply current.
• 10 kV/µs minimum common mode rejection (CMR)
at VCM = 1000 V.
• Wide VCC operating range: 10 V to 30 V over
temperature range.
• Wide operating temperature range: –40°C to 100°C.
Applications
• Isolated IGBT/Power MOSFET gate drive
• AC and brushless DC motor drives
• Industrial inverters
• Inverter for home appliances
• Induction cooker
• Switching Power Supplies (SPS)
CAUTION: It is advised that normal static precautions be taken
in handling and assembly of this component to prevent
damage and/or degradation which may be induced by ESD.
|
| |
 
Table 1. IEC/EN/DIN EN 60747-5-2 Insulation Characteristics* (ACPL-P314/W314 Option 060)
Description
Symbol Characteristic Unit
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤ 150Vrms
for rated mains voltage ≤ 300Vrms
for rated mains voltage ≤ 600Vrms
Climatic Classification
I - IV
I - III
I - II
55/100/21
Pollution Degree (DIN VDE 0110/1.89)
2
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
VIORM x 1.875=VPR, 100% Production Test with tm=1 sec, Partial discharge < 5 pC
Input to Output Test Voltage, Method a*
VIORM x 1.5=VPR, Type and Sample Test, tm=60 sec, Partial discharge < 5 pC
Highest Allowable Overvoltage (Transient Overvoltage tini = 10 sec)
Safety-limiting values - maximum values allowed in the event of a failure.
Case Temperature
Input Current**
Output Power**
Insulation Resistance at TS, VIO = 500 V
VIORM
VPR
VPR
VIOTM
630
1181
945
6000
TS
IS, INPUT
PS, OUTPUT
RS
175
230
600
>109
Vpeak
Vpeak
Vpeak
Vpeak
°C
mA
mW
* Refer to the optocoupler section of the Isolation and Control
Components Designer’s Catalog, under Product Safety
Regulations section, (IEC/EN/DIN EN 60747-5-2) for a detailed
description of Method a and Method b partial discharge test
profiles.
** Refer to the following figure for dependence of PS and IS on
ambient temperature.
Table 2. Insulation and Safety Related Specifications
Parameter
Minimum External Air Gap
(External Clearance)
Minimum External
Tracking (External Creepage)
Minimum Internal Plastic Gap
(Internal Clearance)
Symbol
L(101)
ACPL-
P314 W314
7.0 8.0
L(102)
8.0 8.0
0.08 0.08
Minimum Internal Tracking
(Internal Creepage)
Tracking Resistance
(Comparative Tracking Index)
Isolation Group
CTI
NA NA
>175 >175
IIIa IIIa
Units
Conditions
mm Measured from input terminals to output
terminals, shortest distance through air.
mm Measured from input terminals to output
terminals, shortest distance path along body.
mm Through insulation distance conductor to
conductor, usually the straight line distance
thickness between the emitter and detector.
mm Measured from input terminals to output
terminals, along internal cavity.
V DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE 0110, 1/89, Table 1)
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for ACPL-P314 electronic component. |
| Information | Total 13 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ ACPL-P314.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| ACPL-P314 | The function is 0.6 Amp Output Current IGBT Gate Driver Optocoupler. Avago Technologies | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
ACPL
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||