DataSheetWiki


SKY77554-21 fiches techniques PDF

Skyworks Solutions - Tx Quad-Band / Rx Dual-Band BiFET iPAC FEM

Numéro de référence SKY77554-21
Description Tx Quad-Band / Rx Dual-Band BiFET iPAC FEM
Fabricant Skyworks Solutions 
Logo Skyworks Solutions 





1 Page

No Preview Available !





SKY77554-21 fiche technique
PRODUCT SUMMARY
SKY77554-21 Tx Quad-Band / Rx Dual-Band BiFET iPACFEM
for GSM / GPRS (824-915 MHz and 1710-1910 MHz)
w/ Dual WCDMA TRx Switch
Applications
Dual-band cellular handsets
encompassing
- Class 4 GSM850/900
- DCS1800/PCS1900
- Class 12 GPRS multi-slot
operation
Features
High efficiency
- 42% (GSM850)
- 42% (GSM900)
- 42% (DCS1800)
- 41% (PCS1900)
Low transmit supply current
- 1.36 A (GSM850)
- 1.36 A (GSM900)
- 0.86 A (DCS1800/PCS1900)
Internal ICC sense resistor for
iPAC
Closed loop iPAC
50 Ω matched Input/Output
Tx–VCO-to-antenna and
antenna-to-Rx-SAW filter RF
interface
RF switch affords high
linearity, low insertion loss,
and 0 V DC on Rx ports
Small, low profile package
- 6 mm x 6 mm x 0.9 mm
- 28-pad configuration
Description
SKY77554-21 is a transmit and receive Front-End Module (FEM) with Integrated Power Amplifier
Control (iPAC) for Dual-band cellular handsets comprising GSM850/900 and DCS1800/PCS1900
operation. Designed in a low profile, compact form factor, the SKY77554-21 offers a complete
Transmit VCO-to-Antenna and Antenna-to-Receive SAW filter solution. The FEM also supports
Class 12 General Packet Radio Service (GPRS) multi-slot operation.
The module consists of a GSM850/900 PA block and a DCS1800/PCS1900 PA block, impedance-
matching circuitry for 50 ohm input and output impedances, Tx harmonics filtering, high linearity /
low insertion loss RF switch, and a Power Amplifier Control (PAC) block with internal current sense
resistor. Two Heterojunction Bipolar Transistor (HBT) PA blocks, a BiFET PAC, and switch control
circuit are fabricated onto a single Gallium Arsenide (GaAs) die. One PA block supports the
GSM850/900 bands and the other PA block supports the DCS1800/PCS1900 bands. Both PA
blocks share common power supply pads to distribute current. The output of each PA block and
the outputs to the two receive pads are connected to the antenna pad through an RF switch. The
GaAs die, Switch die and passive components are mounted on a multi-layer laminate substrate.
The assembly is encapsulated with plastic overmold.
Band selection and control of transmit and receive are performed using four external control pads.
Refer to the block diagram in Figure 1 below. The band select pad, BS, selects GSM850, GSM900,
DCS, and PCS modes of operation.
Transmit enable TxEN controls receive or transmit mode of the RF switch (Tx = logic 1) and sets
the turn-on threshold for VRAMP (VRAMP threshold = V(TxEN) ÷ 7). Proper timing between transmit
enable TxEN and Analog Power Control VRAMP allows for high isolation between the antenna and
Tx–VCO while the VCO is being tuned prior to the transmit burst.
The SKY77554-21 is compatible with logic levels from 1.2 V to 2.9 V for BS, TxEN, MODE, and
VSW_EN pads.
Figure 1. SKY77554-21 Functional Block Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201482A • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice. • February 8, 2011
1

PagesPages 2
Télécharger [ SKY77554-21 ]


Fiche technique recommandé

No Description détaillée Fabricant
SKY77554-21 Tx Quad-Band / Rx Dual-Band BiFET iPAC FEM Skyworks Solutions
Skyworks Solutions

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche