DataSheetWiki


EY3A-110-A fiches techniques PDF

Omron - Single Beam Sensor

Numéro de référence EY3A-110-A
Description Single Beam Sensor
Fabricant Omron 
Logo Omron 





1 Page

No Preview Available !





EY3A-110-A fiche technique
Single Beam Sensor (1 Beam: 100 mm)
EY3A-110-A
Dimensions
Note: All units are in millimeters unless otherwise indicated.
Center of
positioning boss
2-R2
41.6±0.1
2.7±0.1
Center of detector
5 dia.
8.3 dia.
R5
Center of emitter
10
40
0.2
dia.
3.05
+0.05
0
dia.
3.6 Pin No. 1
3.2
0
0.2
dia.
30±0.1
58
64.4
17
Pin no. Remarks
Name
1O
Output (OUT)
2V
3G
Power supply (Vcc)
Ground (GND)
Unless otherwise specified, the
tolerances are as shown below.
Dimensions
3 mm max.
3 < mm 6
6 < mm 10
10 < mm 18
18 < mm 30
30 < mm 50
50 < mm 80
Tolerance
±0.3
±0.375
±0.45
±0.55
±0.65
±0.8
±0.95
Recommended Mating Connectors:
Tyco Electronics AMP 173977-3 (press-fit connector)
179228-3 (crimp connector)
175778-3 (crimp connector)
Features
Ensures higher sensitivity and external light interference resistivity
than any other photomicrosensor.
Narrow sensing range ensures stable sensing of a variety of sens-
ing objects.
Absolute Maximum Ratings (Ta = 25° C)
Item
Power supply voltage
Load voltage
Load current
Ambient
temperature
Operating
Storage
Symbol
VCC
VOUT
IOUT
Topr
Tstg
Rated value
7V
7V
10 mA
0° C to 60° C
–15° C to 70° C
Note: Make sure there is no icing or condensation when operating the
Sensor.
Ordering Information
Description
Single beam sensor
Model
EY3A-110-A
Electrical and Optical Characteristics (Ta = 0° C to 60° C)
Item
Power supply voltage
Current consumption
Peak current consumption
Low-level output voltage
High-level output voltage
Response delay time (high to low)
Response delay time (low to high)
Value
5 V ±5%
50 mA max.
200 mA max.
0.6 V max.
3.5 V min.
1.5 ms max.
1.5 ms max.
Condition
---
VCC = 5 V, RL =
VCC = 5 V, RL =
VCC = 5 V, IOL = 4 mA (see note 1)
VCC = 5 V, RL = 4.7 k(see note 2)
The time required for the output to become “Lo” after placing
sensing object.
The time required for the output to become “Hi” after removing
sensing object.
Note: 1. These conditions are for the sensing of lusterless paper with an OD of 0.9 maximum located at the correct sensing position of the Sensor
as shown in the optical path arrangement on the next page.
2. These conditions are for the sensing of the paper supporting plate with an OD of 0.05 located using the glass plate without paper as
shown in the optical path arrangement on the next page.
134 Single Beam Sensor (1 Beam: 100 mm) EY3A-110-A

PagesPages 2
Télécharger [ EY3A-110-A ]


Fiche technique recommandé

No Description détaillée Fabricant
EY3A-110-A Single Beam Sensor Omron
Omron

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche