DataSheetWiki


3064 fiches techniques PDF

Allegro MicroSystems - HALL-EFFECT GEAR-TOOTH SENSOR

Numéro de référence 3064
Description HALL-EFFECT GEAR-TOOTH SENSOR
Fabricant Allegro MicroSystems 
Logo Allegro MicroSystems 





1 Page

No Preview Available !





3064 fiche technique
3064
HALL-EFFECT GEAR-TOOTH SENSOR
—AC COUPLED
XX
VCC
12 34 5
Dwg. PH-011-1
Pinning is shown viewed from branded side.
ABSOLUTE MAXIMUM RATINGS
at TA = +25°C
Supply Voltage, VCC ............................. 24 V
Reverse Battery Voltage, VRCC .......... -30 V
Magnetic Flux Density, B ............ Unlimited
Output Off Voltage, VOUT ...................... 24 V
Output Current, IOUT ......................... 25 mA
Package Power Dissipation,
PD ............................................ 500 mW
Operating Temperature Range,
TA ............................... -40°C to +150°C
Storage Temperature Range,
TS ............................... -65°C to +170°C
The A3064LKA ac-coupled Hall-effect gear-tooth sensor is a
monolithic integrated circuit that switches in response to changing
differential magnetic fields created by moving ferrous targets. This
device is ideal for use in non-zero-speed, gear-tooth-based speed,
position, and timing applications such as in anti-lock braking systems,
transmissions, and crankshafts.
When coupled with a back-biasing magnet, the sensor can be
configured to turn on or off with the leading or trailing edge of a gear-
tooth or slot. Changes in fields on the magnet face caused by a moving
ferrous mass are sensed by two integrated Hall transducers and are
differentially amplified by on-chip electronics. This differential
sensing design provides immunity to radial vibration within the
device’s operating air gap. Steady-state magnet and system offsets are
eliminated using an on-chip differential band-pass filter. This filter
also provides relative immunity to interference from RF and electro-
magnetic sources. The on-chip temperature compensation and Schmitt
trigger circuitry minimizes shifts in effective working air gaps and
switch points over temperature, allowing operation to low frequencies
over a wide range of air gaps and temperatures.
Each Hall-effect digital Integrated circuit includes a voltage
regulator, two quadratic Hall-effect sensing elements, temperature
compensating circuitry, a low-level amplifier, band-pass filter, Schmitt
trigger, and an open-collector output driver. The on-board regulator
permits operation with supply voltages of 4.5 to 24 volts. The output
stage can easily switch 20 mA over the full frequency response range
of the sensor and is compatible with bipolar and MOS logic circuits.
The device is packaged in a 5-pin plastic SIP.
FEATURES
s Senses Motion of Ferrous Targets
s Wide Operating Temperature Range
s Operation to 30 kHz
s Resistant to EMI
s Large Effective Air Gap
s 4.5 V to 24 V Operation
s Output Compatible With All Logic Families
s Reverse Battery Protection
s Resistant to Physical Stress
Always order by complete part number, e.g., A3064LKA .

PagesPages 8
Télécharger [ 3064 ]


Fiche technique recommandé

No Description détaillée Fabricant
3064 HALL-EFFECT GEAR-TOOTH SENSOR Allegro MicroSystems
Allegro MicroSystems
3068N CXA3068N Sony Corporation
Sony Corporation
306DCR2R3STV Super Capacitors Illinois Capacitor
Illinois Capacitor

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche