|
|
PDF LC121S1-A1MT Data sheet ( Hoja de datos )
| Número de pieza | LC121S1-A1MT | |
| Descripción | SVGA TFT LCD | |
| Fabricantes | LG | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LC121S1-A1MT (archivo pdf) en la parte inferior de esta página. Total 22 Páginas | ||
|
No Preview Available !
LC121S1-A1MT LIQUID CRYSTAL DISPLAY
SPECIFICATIONS
TITLE: LC121S1-A1MT REV. 1 PAGE 1 OF 22
DATA DISPLAY AG
LC121S1-A1MT
12.1“ SVGA TFT LCD
PRELIMINARY
SPECIFICATION
The information given in this document is carefully checked and believed to be reliable. Data Display reserves the right to
make changes in product or specification at any time and without further notice. Data Display products are not intended for
use in systems in which failures of product could result in personal injury. All mentioned trademarks are registered
trademarks of their owner.
LG.Philips LCD: Rev. 1.3, JAN 30, 2001
DATA DISPLAY AG
Industriestrasse 1
D-82110 Germering
JUNE 2001
http://www.datadisplay.de
Tel.: +49-89-894450-0
Fax: +49-89-894450-90
1 page  
SPECIFICATIONS
LC121S1-A1MT LIQUID CRYSTAL DISPLAY
TITLE: LC121S1-A1MT REV. 1 PAGE 5 OF 22
Note 6:
Note 7:
Note 8:
Note 9:
The output of the inverter must have symmetrical(negative and positive)
voltage waveform and symmetrical current waveform.(Unsymmetrical
ratio is less than 10%) Please do not use the inverter which has
unsymmetrical voltage and unsymmetrical current and spike wave.
Lamp frequency may produce interface with horizontal synchronous
frequency and as a result this may cause beat on the display. Therefore
lamp frequency shall be as away possible from the horizontal
synchronous frequency and from its harmonics in order to prevent
interference.
Let’s define the brightness of the lamp after being lighted for 5 minutes
as 100%.
TS is the time required for the brightness of the center of the lamp to be
not less than 95%.
The lamp power consumption shown above does not include loss of
external inverter.
The used lamp current is the lamp typical current.
The life is determined as the time at which brightness of the lamp is 50%
compared to that of initial value at the typical lamp current on condition of
continuous operating at 25 ± 2°C.
Note 10: Do not attach a conducting tape to lamp connecting wire.
If the lamp wire attach to a conducting tape, TFT-LCD Module has a low
luminance and the inverter has abnormal action. Because leakage
current is occurred between lamp wire and conducting tape.
3.2 Interface Connections
Interface chip must be used FlatLink, part No. THC63LVDM63A(Transmitter),
THC63LVDF64A(Receiver)
made by Thine Microsystems, Inc.
This LCD employs two interface connections, a 20 pin connector is used for the
module electronics and the
other connector is used for the integral backlight system.
The electronics interface connector is a model DF19K-20P-1H manufactured by
HIROSE.
The pin configuration for the connector is shown in the table below.
DATA DISPLAY AG
Industriestrasse 1
D-82110 Germering
JUNE 2001
http://www.datadisplay.de
Tel.: +49-89-894450-0
Fax: +49-89-894450-90
5 Page 
LC121S1-A1MT LIQUID CRYSTAL DISPLAY
3.6 Power Sequence
SPECIFICATIONS
TITLE: LC121S1-A1MT REV. 1 PAGE 11 OF 22
Power Supply For
LCD
VCC
Interface Signal,
Vi
(LVDS Signal of
Transmitter)
90%
10
0V%
T2
T1
Valid
0V
Data
T3
90%
T5 T6
10
%
T7
T4
Power for Lamp
OFF
LAMP
ON
OFF
Parameter
T1
T2
T3
T4
T5
T6
T7
Values
Min. Typ.
Max.
--
0-
200 -
200 -
0-
--
400 -
10
50
-
-
50
10
-
Units
ms
ms
ms
ms
ms
ms
ms
Note 1:
Note 2:
Note 3:
Please avoid floating state of interface signal at invalid period.
When the interface signal is invalid, be sure to pull down the power
supply for LCD VCC to 0 V.
Lamp power must be turn on after power supply for LCD and interface
signal are valid.
DATA DISPLAY AG
Industriestrasse 1
D-82110 Germering
JUNE 2001
http://www.datadisplay.de
Tel.: +49-89-894450-0
Fax: +49-89-894450-90
11 Page | ||
| Páginas | Total 22 Páginas | |
| PDF Descargar | [ Datasheet LC121S1-A1MT.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LC121S1-A1MT | SVGA TFT LCD | LG |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |