|
|
PDF BTS5235-2L Data sheet ( Hoja de datos )
| Número de pieza | BTS5235-2L | |
| Descripción | Smart High-Side Power Switch | |
| Fabricantes | Infineon Technologies | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de BTS5235-2L (archivo pdf) en la parte inferior de esta página. Total 29 Páginas | ||
|
No Preview Available !
Target Data Sheet, V1.2, Aug 2006
BTS 5235-2L
Smart High-Side Power Switch
PROFET
Two Channels, 60 mΩ
Automotive Power
1 page  
Smart High-Side Power Switch
BTS 5235-2L
Overview
1 Overview
The BTS 5235-2L is a dual channel high-side power switch (two times 60 mΩ) in
PG-DSO-12-9 power package providing embedded protective functions.
The Enhanced IntelliSense pins IS1 and IS2 provide a sophisticated diagnostic feedback
signal including current sense function, over load and over temperature alerts in ON-
state and open load alert in OFF-state. The diagnosis signals can be switched on and
off by the sense enable pin SEN.
An integrated ground resistor as well as integrated resistors at each input pin (IN1, IN2,
SEN) reduce external components to a minimum.
The power transistor is built by a N-channel vertical power MOSFET with charge pump.
The inputs are ground referenced CMOS compatible. The device is monolithically
integrated in Smart SIPMOS technology.
1.1 Block Diagram
channel 1
IN1
IS1
SEN
internal
power
supply
ESD
protection
channel 2
IN2
IS2
logic
load current
sense
gate control
&
charge pump
open load
detection
clamp for
inductive load
multi step
load current
limitation
temperature sensor
over load detection
control and protection circuit
equivalent to
channel 1
Figure 1 Block Diagram
RGND
GND
VBB
OUT1
OUT2
Target Data Sheet
5
V1.2, 2006-08-08
5 Page 
Smart High-Side Power Switch
BTS 5235-2L
Block Description and Electrical Characteristics
A high signal at the input pin causes the power DMOS to switch on with a dedicated
slope, which is optimized in terms of EMC emission.
Figure 6
IN
VOUT
90%
70%
30%
10%
tON
dV /dtON
Switching a Load (resistive)
tOFF t
70%
dV /dtOFF
30%
t
SwitchOn.emf
4.1.3 Inductive Output Clamp
When switching off inductive loads with high-side switches, the voltage VOUT drops below
ground potential, because the inductance intends to continue driving the current.
Vbb
VBB
GND
IL
OUT VOUT
L,
RL
Figure 7 Output Clamp (OUT1 and OUT2)
OutputClamp.emf
To prevent destruction of the device, there is a voltage clamp mechanism implemented
that keeps that negative output voltage at a certain level (VOUT(CL)). See Figure 7 and
Figure 8 for details. Nevertheless, the maximum allowed load inductance is limited.
Target Data Sheet
11
V1.2, 2006-08-08
11 Page | ||
| Páginas | Total 29 Páginas | |
| PDF Descargar | [ Datasheet BTS5235-2L.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| BTS5235-2G | Smart High-Side Power Switch | Infineon Technologies |
| BTS5235-2L | Smart High-Side Power Switch | Infineon Technologies |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |