|
|
Número de pieza | MB9BF104NA | |
Descripción | 32-bit ARM Cortex-M3 based Microcontroller | |
Fabricantes | Fujitsu | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de MB9BF104NA (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! FUJITSU SEMICONDUCTOR
DATA SHEET
DS706-00020-1v0-E
32-bit ARMTM CortexTM-M3 based Microcontroller
MB9B100A Series
MB9BF102NA/RA, F104NA/RA, F105NA/RA,
F106NA/RA
DESCRIPTION
This series are a highly integrated 32-bit microcontroller that target for high-performance and cost-sensitive
embedded control applications.
This series are based on the ARM Cortex-M3 Processor and on-chip Flash memory and SRAM, and
peripheral functions, including Motor Control Timers, ADCs and Communication Interfaces (UART, CSIO,
I2C, LIN).
The products which are described in this data sheet are placed into TYPE0 product categories in
"FM3FAMILY MB9Axxx/MB9Bxxx SERIES PERIPHERAL MANUAL".
Note: ARM and Cortex are the trademarks of ARM Limited in the EU and other countries.
Copyright©2011 FUJITSU SEMICONDUCTOR LIMITED All rights reserved
2011.8
1 page MB9B100A Series
CRC (Cyclic Redundancy Check) Accelerator
The CRC accelerator helps a verify data transmission or storage integrity.
CCITT CRC16 and IEEE-802.3 CRC32 are supported.
・CCITT CRC16 Generator Polynomial: 0x1021
・IEEE-802.3 CRC32 Generator Polynomial: 0x04C11DB7
Clock and Reset
[Clocks]
Five clock sources (2 ext. osc, 2 CR osc, and Main PLL) that are dynamically selectable.
・Main Clock
: 4MHz to 48MHz
・Sub Clock
: 32.768kHz
・High-speed CR Clock : 4MHz
・Low-speed CR Clock : 100kHz
・Main PLL Clock
[Resets]
Reset requests from INITX pins, Power on reset, Software reset, watchdog timers reset, low voltage
detector reset and clock supervisor reset.
Clock Super Visor (CSV)
Clocks generated by CR oscillators are used to supervise abnormality of the external clocks.
・External OSC clock failure (clock stop) is detected, reset is asserted.
・External OSC frequency anomaly is detected, interrupt or reset is asserted.
Low Voltage Detector (LVD)
This series include 2-stage monitoring of voltage on the VCC. When the voltage falls below the voltage has
been set, Low Voltage Detector generates an interrupt or reset.
・LVD1: error reporting via interrupt
・LVD2: auto-reset operation
Low Power Mode
Three power saving modes supported.
・ SLEEP
・ TIMER
・ STOP
Debug
・Serial Wire JTAG Debug Port (SWJ-DP)
・Embedded Trace Macrocells (ETM) provide comprehensive debug and trace facilities.
Power Supply
Two Power Supplies
・VCC = 2.7V to 5.5V: Correspond to the wide range voltage.
DS706-00020-1v0-E
5
5 Page z BGA-112P-M04
MB9B100A Series
<Note>
The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated
port number. For these pins, there are multiple pins that provide the same function for the same channel.
Use the extended port function register (EPFR) to select the pin.
DS706-00020-1v0-E
11
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet MB9BF104NA.PDF ] |
Número de pieza | Descripción | Fabricantes |
MB9BF104N | 32-bit Microcontroller | Fujitsu |
MB9BF104NA | Microcontroller | Spansion |
MB9BF104NA | 32-bit ARM Cortex-M3 based Microcontroller | Fujitsu |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |