|
|
Número de pieza | MTB36N06V | |
Descripción | Power MOSFET ( Transistor ) | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de MTB36N06V (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
No Preview Available ! MTB36N06V
Preferred Device
Power MOSFET
32 Amps, 60 Volts
N−Channel D2PAK
This Power MOSFET is designed to withstand high energy in the
avalanche and commutation modes. Designed for low voltage, high
speed switching applications in power supplies, converters and power
motor controls, these devices are particularly well suited for bridge
circuits where diode speed and commutating safe operating areas are
critical and offer additional safety margin against unexpected voltage
transients.
• Avalanche Energy Specified
• IDSS and VDS(on) Specified at Elevated Temperature
MAXIMUM RATINGS (TC = 25°C unless otherwise noted)
Rating
Symbol Value Unit
Drain−to−Source Voltage
Drain−to−Gate Voltage (RGS = 1.0 MΩ)
Gate−to−Source Voltage
− Continuous
− Non−Repetitive (tp ≤ 50 μs)
Drain Current − Continuous @ 25°C
Drain Current − Continuous @ 100°C
Drain Current − Single Pulse (tp ≤ 10 μs)
Total Power Dissipation @ 25°C
Derate above 25°C
Total Power Dissipation @ TA = 25°C
(Note 1.)
VDSS
VDGR
VGS
VGSM
ID
ID
IDM
PD
60 Vdc
60 Vdc
± 20
± 25
32
22.6
112
90
0.6
3.0
Vdc
Vpk
Adc
Apk
Watts
W/°C
Watts
Operating and Storage Temperature
Range
TJ, Tstg
− 55 to
175
°C
Single Pulse Drain−to−Source Avalanche
Energy − Starting TJ = 25°C
(VDD = 25 Vdc, VGS = 10 Vdc, Peak
IL = 32 Apk, L = 0.1 mH, RG = 25 Ω)
EAS
205 mJ
Thermal Resistance
− Junction to Case
− Junction to Ambient
− Junction to Ambient (Note 1.)
RθJC
RθJA
RθJA
°C/W
1.67
62.5
50
Maximum Lead Temperature for Soldering
Purposes, 1/8″ from Case for 10
seconds
TL
260 °C
1. When surface mounted to an FR4 board using the minimum recommended
pad size.
http://onsemi.com
32 AMPERES
60 VOLTS
RDS(on) = 40 mΩ
N−Channel
D
G
S
12
3
4
D2PAK
CASE 418B
STYLE 2
MARKING DIAGRAM
& PIN ASSIGNMENT
4
Drain
MTB36N06V
YWW
12
Gate Drain
3
Source
MTB36N06V
Y
WW
= Device Code
= Year
= Work Week
ORDERING INFORMATION
Device
Package
Shipping
MTB36N06V
MTB36N06VT4
D2PAK
D2PAK
50 Units/Rail
800/Tape & Reel
Preferred devices are recommended choices for future use
and best overall value.
© Semiconductor Components Industries, LLC, 2006
August, 2006 − Rev. 4
1
Publication Order Number:
MTB36N06V/D
1 page MTB36N06V
12
10
8
Q1
6
QT
Q2
VGS
30
25
20
15
4
2 Q3
10
TJ = 25°C
ID = 32 A 5
VDS
00
0 5 10 15 20 25 30 35 40
QT, TOTAL CHARGE (nC)
Figure 8. Gate−To−Source and Drain−To−Source
Voltage versus Total Charge
1000
TJ = 25°C
ID = 32 A
VDD = 30 V
VGS = 10 V
100
tr
tf
td(off)
10 td(on)
1
1 10
RG, GATE RESISTANCE (OHMS)
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
DRAIN−TO−SOURCE DIODE CHARACTERISTICS
32
TJ = 25°C
VGS = 0 V
24
100
16
8
0
0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 0.95 1 1.05
VSD, SOURCE−TO−DRAIN VOLTAGE (VOLTS)
Figure 10. Diode Forward Voltage versus Current
SAFE OPERATING AREA
The Forward Biased Safe Operating Area curves define
the maximum simultaneous drain−to−source voltage and
drain current that a transistor can handle safely when it is
forward biased. Curves are based upon maximum peak
junction temperature and a case temperature (TC) of 25°C.
Peak repetitive pulsed power limits are determined by using
the thermal response data in conjunction with the procedures
discussed in AN569, “Transient Thermal
Resistance−General Data and Its Use.”
Switching between the off−state and the on−state may
traverse any load line provided neither rated peak current
(IDM) nor rated voltage (VDSS) is exceeded and the
transition time (tr,tf) do not exceed 10 μs. In addition the total
power averaged over a complete switching cycle must not
exceed (TJ(MAX) − TC)/(RθJC).
A Power MOSFET designated E−FET can be safely used
in switching circuits with unclamped inductive loads. For
reliable operation, the stored energy from circuit inductance
dissipated in the transistor while in avalanche must be less
than the rated limit and adjusted for operating conditions
differing from those specified. Although industry practice is
to rate in terms of energy, avalanche energy capability is not
a constant. The energy rating decreases non−linearly with an
increase of peak current in avalanche and peak junction
temperature.
Although many E−FETs can withstand the stress of
drain−to−source avalanche at currents up to rated pulsed
current (IDM), the energy rating is specified at rated
continuous current (ID), in accordance with industry
custom. The energy rating must be derated for temperature
as shown in the accompanying graph (Figure 12). Maximum
energy at currents below rated continuous ID can safely be
assumed to equal the values indicated.
http://onsemi.com
5
5 Page |
Páginas | Total 10 Páginas | |
PDF Descargar | [ Datasheet MTB36N06V.PDF ] |
Número de pieza | Descripción | Fabricantes |
MTB36N06E | TMOS POWER FET 36 AMPERES 60 VOLTS | Motorola Semiconductors |
MTB36N06V | TMOS POWER FET 32 AMPERES 60 VOLTS | Motorola Semiconductors |
MTB36N06V | Power MOSFET ( Transistor ) | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |