|
|
PDF AP7315 Data sheet ( Hoja de datos )
| Número de pieza | AP7315 | |
| Descripción | 150mA HIGH PSRR LOW NOISE LDO | |
| Fabricantes | Diodes | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AP7315 (archivo pdf) en la parte inferior de esta página. Total 23 Páginas | ||
|
No Preview Available !
AP7315
150mA HIGH PSRR LOW NOISE LDO WITH ENABLE
Description
The AP7315 is a low dropout regulator with high output voltage
accuracy, low RDS(ON), high PSRR, low output noise and low
quiescent current. This regulator is based on a CMOS process.
Pin Assignments
The AP7315 includes a voltage reference, error amplifier, current limit
circuit and an enable input to turn it on and off. With the integrated
resistor network fixed output voltage versions can be delivered.
With its low power consumption and line and load transient response,
the AP7315 is well suited for low power handheld communication
equipment.
The AP7315 is packaged in X2-DFN1010-4, SOT23 and SOT25
packages and allows for smallest footprint and dense PCB layout.
Features
Low VIN and Wide VIN Range: 1.7V to 5.25V
Guarantee Output Current,150mA
VOUT Accuracy ±1%
Ripple Rejection 75dB at 1kHz
Low Output Noise, 60µVrms from 10Hz to 100kHz
Quiescent Current as Low as 35µA
VOUT Fixed 1.1V to 3.3V
Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
Halogen and Antimony Free, Green Device (Note 3)
Applications
Smart Phone/PAD
RF Supply
Cameras
Portable Video
Portable Media Player
Wireless Adapter
Wireless Communication
Pin 1 – VOUT, Pin 2 – GND, Pin 3 – EN, Pin 4 – VIN
(Top View)
GND
3
(Top View)
VIN
3
12
VIN VOUT
SOT23 (SA)
1
GND
2
VOUT
SOT23 (SR)
(Top View)
VOUT
NC
54
1 23
VIN GND EN/NC
SOT25
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free,"Green"
and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.
AP7315
Document number: DS38352 Rev. 1 - 2
1 of 23
www.diodes.com
December 2015
© Diodes Incorporated
1 page  
Typical Characteristics
Output Voltage vs. Output Current
AP7315-18
2.1
1.8
VIN=2.8V
1.5 VIN=3.6V
VIN=4.2V
1.2
VIN=5V
VIN=5.5V
0.9
0.6
0.3
0.0
0
100 200 300 400
Output Current IOUT (mA)
500
Output Voltage vs. Output Current
AP7315-33
3.5
3.0
2.5
VIN=4.3V
VIN=5V
VIN=5.5V
2.0
1.5
1.0
0.5
0.0
0
100 200 300 400
Output Current IOUT (mA)
500
AP7315
Output Voltage vs. Output Current
AP7315-25
3.0
2.5
VIN=3.5V
2.0 VIN=4.2V
VIN=5V
VIN=5.5V
1.5
1.0
0.5
0.0
0
100 200 300 400
Output Current IOUT (mA)
500
Output Noise (AP7315-33)
Output Voltage vs. Intput Voltage
AP7315-25
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
IOUT=1mA
IOUT=30mA
IOUT=50mA
123
Input Voltage VIN (V)
4
5
Output Voltage vs. Intput Voltage
AP7315-33
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
123
Input Voltage VIN (V)
IOUT=1mA
IOUT=30mA
IOUT=50mA
45
AP7315
Document number: DS38352 Rev. 1 - 2
5 of 23
www.diodes.com
December 2015
© Diodes Incorporated
5 Page 
AP7315
Application Information
Output Capacitor
An output capacitor (COUT) is needed to improve transient response and maintain stability. The AP7315 is stable with very small ceramic output
capacitors. The ESR (equivalent series resistance) and capacitance drives the selection. If the application has large load variations, it is
recommended to utilize low-ESR bulk capacitors. It is recommended to place ceramic capacitors as close as possible to the load and the ground
pin and care should be taken to reduce the impedance in the layout.
Input Capacitor
To prevent the input voltage from dropping during load steps it is recommended to utilize an input capacitor (CIN). A minimum 0.47μF ceramic
capacitor is recommended between VIN and GND pins to decouple input power supply glitch. This input capacitor must be located as close as
possible to the device to assure input stability and reduce noise. For PCB layout, a wide copper trace is required for both VIN and GND pins.
Enable Control
The AP7315 is turned on by setting the EN pin high, and is turned off by pulling it low. If this feature is not used, the EN pin should be tied to VIN pin
to keep the regulator output on at all time. To ensure proper operation, the signal source used to drive the EN pin must be able to swing above and
below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section.
Short Circuit Protection
When VOUT pin is short-circuit to GND, short circuit protection will be triggered and clamp the output current to approximately 60mA. This feature
protects the regulator from over-current and damage due to overheating.
Layout Considerations
For good ground loop and stability, the input and output capacitors should be located close to the VIN, VOUT, and GND pins of the device. The
regulator GND pin should be connected to the external circuit ground to reduce voltage drop caused by trace impedance. Ground plane is generally
used to reduce trace impedance. Wide trace should be used for large current paths from VIN to VOUT, and load circuit.
ESR vs. Output Current
Ceramic type output capacitor is recommended for this series; however, the other output capacitors with low ESR also can be used. The relations
between IOUT (Output Current) and ESR of an output capacitor are shown below. The stable region is marked as the hatched area in the graph.
Measurement conditions:
Frequency Band: 10Hz to 2MHz, Temperature: -40°C to +85°C
ESR vs. Output Current
AP7315-18
100
ESR vs. Output Current
AP7315-33
100
10
1
Stable Range
0.1
-40°C
85°C
10
1
Stable Range
0.1
-40°C
85°C
0.01
0.01
0.001
0
25 50 75 100 125 150
Output Current IOUT (mA)
0.001
0
25 50 75 100
Output Current IOUT (mA)
125
150
AP7315
Document number: DS38352 Rev. 1 - 2
11 of 23
www.diodes.com
December 2015
© Diodes Incorporated
11 Page | ||
| Páginas | Total 23 Páginas | |
| PDF Descargar | [ Datasheet AP7315.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AP7311 | Fast Transient Low Dropout Linear Regulator | Diodes |
| AP7312 | DUAL 150mA LOW QUIESCENT CURRENT FAST TRANSIENT LOW DROPOUT | Diodes |
| AP7313 | Fast Transient Low Dropout Linear Regulator | Diodes |
| AP7315 | 150mA HIGH PSRR LOW NOISE LDO | Diodes |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |