|
|
PDF MKL26Z64VLH4 Data sheet ( Hoja de datos )
| Número de pieza | MKL26Z64VLH4 | |
| Descripción | 48 MHz Cortex-M0+ Based Microcontroller | |
| Fabricantes | Freescale Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MKL26Z64VLH4 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Freescale Semiconductor, Inc.
Data Sheet: Technical Data
Document Number: KL26P64M48SF5
Rev 5 08/2014
Kinetis KL26 Sub-Family
48 MHz Cortex-M0+ Based Microcontroller
MKL26ZxxxVFM4
MKL26ZxxxVFT4
MKL26ZxxxVLH4
Designed with efficiency in mind. Compatible with all other
Kinetis L families as well as Kinetis K2x family. General purpose
MCU with USB 2.0, featuring market leading ultra low-power to
provide developers an appropriate entry-level 32-bit solution.
32-pin QFN (FM)
48-pin QFN (FT)
This product offers:
5 x 5 x 1 Pitch 0.5 mm 7 x 7 x 1 Pitch 0.5 mm
• Run power consumption down to 40 μA/MHz in very low
power run mode
• Static power consumption down to 2 μA with full state
retention and 4.5 μs wakeup
• Ultra-efficient Cortex-M0+ processor running up to 48 MHz
with industry leading throughput
64-pin LQFP (LH)
10 x 10 x 1.4 Pitch 0.5 mm
• Memory option is up to 128 KB flash and 16 KB RAM
• Energy-saving architecture is optimized for low power with
90nm TFS technology, clock and power gating techniques, and zero wait state flash memory controller
Performance
Human-machine interface
• 48 MHz ARM® Cortex®-M0+ core
• Low-power hardware touch sensor interface (TSI)
• Up to 50 general-purpose input/output (GPIO)
Memories and memory interfaces
• Up to 128 KB program flash memory
Communication interfaces
• Up to 16 KB SRAM
• USB full-/low-speed On-the-Go controller with on-
chip transceiver and 5 V to 3.3 V regulator
System peripherals
• Two 16-bit SPI modules
• Nine low-power modes to provide power optimization
• I2S (SAI) module
based on application requirements
• One low power UART module
• COP Software watchdog
• Two UART modules
• 4-channel DMA controller, supporting up to 63 request
• Two I2C module
sources
• Low-leakage wakeup unit
Analog Modules
• SWD debug interface and Micro Trace Buffer
• Bit Manipulation Engine
• 16-bit SAR ADC
• 12-bit DAC
Clocks
• 32 kHz to 40 kHz or 3 MHz to 32 MHz crystal oscillator
• Analog comparator (CMP) containing a 6-bit DAC
and programmable reference input
• Multi-purpose clock source
Timers
Operating Characteristics
• Six channel Timer/PWM (TPM)
• Two 2-channel Timer/PWM modules
• Voltage range: 1.71 to 3.6 V
• Periodic interrupt timers
• Flash write voltage range: 1.71 to 3.6 V
• 16-bit low-power timer (LPTMR)
• Temperature range (ambient): -40 to 105°C
• Real time clock
Freescale reserves the right to change the detail specifications as may be required to
permit improvements in the design of its products. © 2013–2014 Freescale
Semiconductor, Inc. All rights reserved.
1 page  
1.4 Voltage and current operating ratings
Table 4. Voltage and current operating ratings
Symbol
VDD
IDD
VIO
ID
VDDA
VUSB_DP
VUSB_DM
VREGIN
Description
Digital supply voltage
Digital supply current
IO pin input voltage
Instantaneous maximum current single pin limit (applies to
all port pins)
Analog supply voltage
USB_DP input voltage
USB_DM input voltage
USB regulator input
Min.
–0.3
—
–0.3
–25
VDD – 0.3
–0.3
–0.3
–0.3
Max.
3.8
120
VDD + 0.3
25
VDD + 0.3
3.63
3.63
6.0
General
Unit
V
mA
V
mA
V
V
V
V
2 General
2.1 AC electrical characteristics
Unless otherwise specified, propagation delays are measured from the 50% to the 50%
point, and rise and fall times are measured at the 20% and 80% points, as shown in the
following figure.
Input Signal
VIH
Midpoint1
Fall Time
Low
VIL
High
Rise Time
80%
50%
20%
The midpoint is VIL + (VIH - VIL) / 2
Figure 1. Input signal measurement reference
All digital I/O switching characteristics, unless otherwise specified, assume the output
pins have the following characteristics.
• CL=30 pF loads
• Slew rate disabled
• Normal drive strength
Kinetis KL26 Sub-Family, Rev5 08/2014.
5
Freescale Semiconductor, Inc.
5 Page 
General
Table 9. Power consumption operating behaviors (continued)
Symbol
IDD_LLS
IDD_VLLS3
IDD_VLLS1
IDD_VLLS0
IDD_VLLS0
Description
Temp.
at 85 °C
at 105 °C
Low leakage stop mode current at 3.0 at 25 °C
V at 50 °C
at 70 °C
at 85 °C
at 105 °C
Very low-leakage stop mode 3 current at 25 °C
at 3.0 V
at 50 °C
at 70 °C
at 85 °C
at 105 °C
Very low-leakage stop mode 1 current at 25 °C
at 3.0V
at 50 °C
at 70 °C
at 85 °C
at 105 °C
Very low-leakage stop mode 0 current
(SMC_STOPCTRL[PORPO] = 0) at
3.0 V
at 25 °C
at 50 °C
at 70 °C
at 85 °C
at 105 °C
Very low-leakage stop mode 0 current
(SMC_STOPCTRL[PORPO] = 1) at
3.0 V
at 25 °C
at 50 °C
at 70 °C
at 85 °C
at 105 °C
Typ.
21.13
45.85
1.98
3.13
5.65
9.58
20.52
1.46
2.29
4.10
6.93
14.80
0.71
1.10
2.09
3.80
8.84
0.40
0.80
1.79
3.50
8.54
0.23
0.61
1.59
3.30
8.36
Max
39.13
85.45
2.65
4.35
8.34
14.29
31.74
2.06
3.22
5.90
10.02
22.12
1.20
1.71
3.03
5.42
12.98
0.88
1.40
2.72
5.10
12.63
0.69
1.19
2.50
4.89
12.41
Unit
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
Note
—
—
—
—
7
1. The analog supply current is the sum of the active or disabled current for each of the analog modules on the device.
See each module's specification for its supply current.
2. MCG configured for PEE mode. CoreMark benchmark compiled using IAR 6.40 with optimization level high, optimized
for balanced.
3. MCG configured for FEI mode.
4. Incremental current consumption from peripheral activity is not included.
5. MCG configured for BLPI mode. CoreMark benchmark compiled using IAR 6.40 with optimization level high, optimized
for balanced.
6. MCG configured for BLPI mode.
7. No brownout.
Kinetis KL26 Sub-Family, Rev5 08/2014.
11
Freescale Semiconductor, Inc.
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet MKL26Z64VLH4.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MKL26Z64VLH4 | 48 MHz Cortex-M0+ Based Microcontroller | Freescale Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |