DataSheetWiki


ISL22323 fiches techniques PDF

Intersil - Dual Digitally Controlled Potentiometer

Numéro de référence ISL22323
Description Dual Digitally Controlled Potentiometer
Fabricant Intersil 
Logo Intersil 





1 Page

No Preview Available !





ISL22323 fiche technique
ISL22323
Dual Digitally Controlled Potentiometer (XDCP™)
Data Sheet
August 17, 2015
FN6422.2
Low Noise, Low Power, I2C® Bus,
256 Taps
The ISL22323 integrates two digitally controlled
potentiometers (DCP), control logic and non-volatile memory
on a monolithic CMOS integrated circuit.
The digitally controlled potentiometer is implemented with a
combination of resistor elements and CMOS switches. The
position of the wipers are controlled by the user through the
I2C bus interface. The potentiometer has an associated
volatile Wiper Register (WRi) and a non-volatile Initial Value
Register (IVRi) that can be directly written to and read by the
user. The contents of the WRi control the position of the
corresponding wiper. At power up the device recalls the
contents of the DCP’s IVRi to the correspondent WRi.
The ISL22323 also has 13 general purpose non-volatile
registers that can be used as storage of lookup table for
multiple wiper position or any other valuable information.
The ISL22323 features a dual supply, that is beneficial for
applications requiring a bipolar range for DCP terminals
between V- and VCC.
Each DCP can be used as three-terminal potentiometers or
as two-terminal variable resistors in a wide variety of
applications including control, parameter adjustments, and
signal processing.
Features
• Two potentiometers in one package
• 256 resistor taps
• I2C serial interface
- Three address pins, up to eight devices per bus
• Non-volatile EEPROM storage of wiper position
• 13 General Purpose non-volatile registers
• High reliability
- Endurance: 1,000,000 data changes per bit per register
- Register data retention: 50 years @ T +55°C
• Wiper resistance: 70typical @ 1mA
• Standby current <4µA max
• Shut-down current <4µA max
• Dual power supply
- VCC = 2.25V to 5.5V
- V- = -2.25V to -5.5V
• 10k 50kor 100ktotal resistance
• Extended industrial temperature range: -40 to +125°C
• 14 Ld TSSOP or 16 Ld QFN
• Pb-free (RoHS compliant)
Block Diagram
SCL
SDA
A2
A1
A0
I2C
INTERFACE
VCC V-
RH0
POWER UP
INTERFACE,
CONTROL
AND
STATUS
LOGIC
NON-VOLATILE
REGISTERS
WR0
VOLATILE
REGISTER
AND
WIPER
CONTROL
CIRCUITRY
RH1
WR1
VOLATILE
REGISTER
AND
WIPER
CONTROL
CIRCUITRY
GND
RW0 RL0
RW1 RL1
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2007, 2008, 2015. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.

PagesPages 19
Télécharger [ ISL22323 ]


Fiche technique recommandé

No Description détaillée Fabricant
ISL22323 Dual Digitally Controlled Potentiometer Intersil
Intersil
ISL22326 Dual Digitally Controlled Potentiometers Intersil Corporation
Intersil Corporation
ISL22326WM Dual Digitally Controlled Potentiometers Intersil
Intersil
ISL22329 Dual Digitally Controlled Potentiometers Intersil Corporation
Intersil Corporation

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche