F59D1G161A Datasheet PDF - Elite Semiconductor
| Part Number | F59D1G161A | |
| Description | 1 Gbit (128M x 8/ 64M x 16) 1.8V NAND Flash Memory | |
| Manufacturers | Elite Semiconductor | |
| Logo |  |
|
|
There is a preview and F59D1G161A download ( pdf file ) link at the bottom of this page. Total 30 Pages | ||
Preview 1 page No Preview Available !
ESMT
Flash
FEATURES
Voltage Supply: 1.8V (1.7 V ~ 1.95V)
Organization
x8:
- Memory Cell Array: (128M + 4M) x 8bit
- Data Register: (2K + 64) x 8bit
x16:
- Memory Cell Array: (64M + 2M) x 16bit
- Data Register: (1K + 32) x 16bit
Automatic Program and Erase
x8:
- Page Program: (2K + 64) Byte
- Block Erase: (128K + 4K) Byte
x16:
- Page Program: (1K + 32) Word
- Block Erase: (64K + 2K) Word
Page Read Operation
- Page Size: (2K + 64) Byte (x8)
Page Size: (1K + 32) Word (x16)
- Random Read: 25us (Max.)
- Serial Access: 45ns (Min.)
Memory Cell: 1bit/Memory Cell
Fast Write Cycle Time
- Program time: 250us (Typ.)
- Block Erase time: 2ms (Typ.)
Command/Address/Data Multiplexed I/O Port
F59D1G81A / F59D1G161A
1 Gbit (128M x 8/ 64M x 16)
1.8V NAND Flash Memory
Hardware Data Protection
- Program/Erase Lockout During Power Transitions
Reliable CMOS Floating Gate Technology
- ECC Requirement: x8 - 1bit/528Byte,
x16 - 1bit/264Word
- Endurance: 100K Program/Erase Cycles
- Data Retention: 10 Years
Command Register Operation
Automatic Page 0 Read at Power-Up Option
- Boot from NAND support
- Automatic Memory Download
NOP: 4 cycles
Cache Program Operation for High Performance Operation
Copy-Back Operation
EDO mode
OTP Operation
No Bad-Block-Erasing-Protect function (user should manage
bad blocks before erasing)
ORDERING INFORMATION
Product ID
x8:
F59D1G81A -45TG
F59D1G81A -45BG
x16:
F59D1G161A -45BG
Speed
45 ns
45 ns
45 ns
Package
48 pin TSOPI
63 ball BGA
63 ball BGA
Comments
Pb-free
Pb-free
Pb-free
Elite Semiconductor Memory Technology Inc.
Publication Date: May 2014
Revision: 1.5
1/43
|
| |
 
ESMT
F59D1G81A / F59D1G161A
Pin Description
Symbol
Pin Name
I/O0~I/O7 (x8)
I/O0~I/O15 (x16)
Data Inputs / Outputs
CLE
Command Latch
Enable
ALE Address Latch Enable
Functions
The I/O pins are used to input command, address and data, and to output data
during read operations. The I/O pins float to Hi-Z when the chip is deselected
or when the outputs are disabled.
The CLE input controls the activating path for commands sent to the command
register. When active high, commands are latched into the command register
through the I/O ports on the rising edge of the WE signal.
The ALE input controls the activating path for address to the internal address
registers. Addresses are latched on the rising edge of WE with ALE high.
CE Chip Enable
The CE input is the device selection control. When the device is in the Busy
state, CE high is ignored, and the device does not return to standby mode in
program or erase operation. Regarding CE control during read operation,
refer to ’Page read’ section of Device operation.
RE Read Enable
The RE input is the serial data-out control, and when active drives the data
onto the I/O bus. Data is valid tREA after the falling edge of RE which also
increments the internal column address counter by one.
WE Write Enable
The WE input controls writes to the I/O port. Commands, address and data
are latched on the rising edge of the WE pulse.
WP Write Protect
The WP pin provides inadvertent program/erase protection during power
transitions. The internal high voltage generator is reset when the WP pin is
active low.
R /B
VCC
VSS
NC
Ready / Busy Output
Power
Ground
No Connection
The R/ B output indicates the status of the device operation. When low, it
indicates that a program, erase or random read operation is in process and
returns to high state upon completion. It is an open drain output and does not
float to Hi-Z condition when the chip is deselected or when outputs are
disabled.
VCC is the power supply for device.
Lead is not internally connected.
Note: Connect all VCC and VSS pins of each device to common power supply outputs. Do not leave VCC or VSS disconnected.
Elite Semiconductor Memory Technology Inc.
Publication Date: May 2014
Revision: 1.5
5/43
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for F59D1G161A electronic component. |
| Information | Total 30 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ F59D1G161A.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| F59D1G161A | The function is 1 Gbit (128M x 8/ 64M x 16) 1.8V NAND Flash Memory. Elite Semiconductor | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
F59D
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||