|
|
PDF APW7165C Data sheet ( Hoja de datos )
| Número de pieza | APW7165C | |
| Descripción | 5V to 12V Synchronous Buck Controller | |
| Fabricantes | Anpec Electronics Coropration | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de APW7165C (archivo pdf) en la parte inferior de esta página. Total 20 Páginas | ||
|
No Preview Available !
APW7165C
5V to 12V Synchronous Buck Controller
Features
General Description
• Wide Operation Supply Voltage from 5V to 12V
• Power-On-Reset Monitoring on VCC
• Excellent Reference Voltage Regulations
- 0.6V Internal Reference
- ±1% Over Temperature Range
• Integrated Soft-Start
• Automatic PSM/PWM Modes
• Voltage Mode PWM Operation with 90% (Max.)
Duty Cycle
• Under-Voltage Protection
• Adjustable Over-Current Protection Threshold
- Sensing the RDS(ON) of Low-Side MOSFET
• Over-Voltage Protection
• Under-Voltage Protection
• Simple SOP-8P Package
• Lead Free and Green Devices Available
(RoHS Compliant)
Applications
• Graphic Cards
• DSL, Switch HUB
• Wireless Lan
• Notebook Computer
• Mother Board
• LCD Monitor/TV
Pin Configuration
The APW7165Cis a voltage mode, fixed 300kHz-switch-
ing frequency, and synchronous buck controller. The
APW7165C allows wide input voltage that is either a
single 5~12V or two supply voltage(s) for various
applications. A power-on-reset (POR) circuit monitors the
VCC supply voltage to prevent wrong logic controls. A built-
in digital soft-start circuit prevents the output voltages from
overshoot as well as limits the input current. An internal
0.6V temperature-compensated reference voltage with
high accuracy is designed to meet the requirement of
low output voltage applications. The APW7165C provides
excellent output voltage regulations against load current
variation.
The controller’s over-current protection monitors the out-
put current by using the voltage drops across the R
DS(ON)
of low-side MOSFET, eliminating the need for a current
sensing resistor that features high efficiency and low cost.
The APW7165C also integrates over-voltage protection
(OVP) and under-voltage protection circuit which moni-
tors the FB voltage to prevent the PWM output from over
and under voltage.
The APW7165C is available in a simple SOP-8P package.
Simplified Application Circuit
OFF
ON
VVCC
APW7165C
5 VCC BOOT 1
7
UGATE 2
COMP
PHASE 8
LGATE 4
6 FB GND
3
VIN
VOUT
BOOT 1
UGATE 2
GND 3
LGATE 4
9
GND
8 PHASE
7 COMP
6 FB
5 VCC
SOP-8P
(Top View)
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and
advise customers to obtain the latest version of relevant information to verify before placing orders.
Copyright © ANPEC Electronics Corp.
Rev. A.2 - Oct., 2012
1
www.anpec.com.tw
1 page  
APW7165C
Operating Waveforms
Refer to the typical application circuit. The test condition is VIN=12V, TA= 25oC unless otherwise specified.
Power On
Power Off
V
IN
1
VOUT
2
V
UGATE
3
CH1: VIN, 5V/Div
CH2: VOUT, 500mV/Div
CH3: VUGATE, 10V/Div
Time: 1ms/Div
1
2
3
CH1: VIN, 5V/Div
CH2: VOUT, 500mV/Div
CH3: VUGATE, 10V/Div
Time: 200ms/Div
VIN
VOUT
V UGATE
Enable
VCOMP
1
VOUT
2
VP H A S E
3
CH1: VCOMP, 1V/Div
CH2: VOUT, 500mV/Div
CH3: VPHASE, 10V/Div
Time: 500µs/Div
Shutdown
RLOAD=10Ω
VCOMP
1
VOUT
2
VP H A S E
3
CH1: VCOMP, 1V/Div
CH2: VOUT, 500mV/Div
CH3: VPHASE, 10V/Div
Time: 1ms/Div
Copyright © ANPEC Electronics Corp.
Rev. A.2 - Oct., 2012
5
www.anpec.com.tw
5 Page 
APW7165C
Function Description (Cont.)
Under-Voltage Protection
The under-voltage function monitors the voltage on FB
(VFB) by Under-Voltage (UV) comparator to protect the PWM
converter against short-circuit conditions. When the VFB
falls below the falling UVP threshold (50% V ), a fault
REF
signal is internally generated and the device turns off
high-side and low-side MOSFETs. The converter is shut-
down and the output is latched to be floating.
Over-Voltage Protection (OVP)
The over-voltage protection monitors the FB voltage to
prevent the output from over-voltage condition. When the
output voltage rises above 120% of the nominal output
voltage, the APW7165C turns off the high-side MOSFET
and turns on the low-side MOSFET until the output volt-
age falls below the falling OVP threshold, regulating the
output voltage around the OVP threshold.
Adaptive Shoot-Through Protection
The gate drivers incorporate an adaptive shoot-through
protection to prevent high-side and low-side MOSFETs
from conducting simultaneously and shorting the input
supply. This is accomplished by ensuring the falling gate
has turned off one MOSFET before the other is allowed to
rise.
During turn-off of the low-side MOSFET, the LGATE volt-
age is monitored until it is below 1.5V threshold, at which
time the UGATE is released to rise after a constant delay.
During turn-off of the high-side OCSFET, the UGATE-to-
PHASE voltage is also monitored until it is below 1.5V
threshold, at which time the LGATE is released to rise
after a constant delay.
Shutdown and Enable
The APW7165C can be shut down or enabled by pulling
low the voltage on COMP. The COMP is a dual-function
pin. During normal operation, this pin represents the
output of the error amplifier. It is used to compensate the
regulation control loop in combination with the FB pin.
Pulling the COMP low (VDISABLE = 0.6V typical) places the
controller into shutdown mode which UGATE and LGATE
are pulled to PHASE and GND respectively.
When the pull-down device is released, the COMP volt-
age will start to rise. When the COMP voltage rises above
the VDISABLE threshold, the APW7165C will begin a new
initialization and soft-start process.
Pulse Skipping Mode (PSM)
At light loads, the inductor current may reach zero or re-
verse on each pulse. The low-side MOSFET is turned off
by the current reversal comparator, IZCMP, to block the
negative inductor current. In this condition, the converter
enters discontinuous current mode operation.
At very light loads, the APW7165C will automatically skip
pulses in pulse skipping mode operation to reduce
switching losses as well as maintain output regulation
for efficient applications.
Copyright © ANPEC Electronics Corp.
Rev. A.2 - Oct., 2012
11
www.anpec.com.tw
11 Page | ||
| Páginas | Total 20 Páginas | |
| PDF Descargar | [ Datasheet APW7165C.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| APW7165 | 5V to 12V Synchronous Buck Controller | Anpec Electronics Coropration |
| APW7165C | 5V to 12V Synchronous Buck Controller | Anpec Electronics Coropration |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |