|
|
PDF AT89C51 Data sheet ( Hoja de datos )
| Número de pieza | AT89C51 | |
| Descripción | 8-Bit Microcontroller with 4K Bytes Flash | |
| Fabricantes | ATMEL Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AT89C51 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
Features
• Compatible with MCS-51™ Products
• 4K Bytes of In-System Reprogrammable Flash Memory
– Endurance: 1,000 Write/Erase Cycles
• Fully Static Operation: 0 Hz to 24 MHz
• Three-Level Program Memory Lock
• 128 x 8-Bit Internal RAM
• 32 Programmable I/O Lines
• Two 16-Bit Timer/Counters
• Six Interrupt Sources
• Programmable Serial Channel
• Low Power Idle and Power Down Modes
Description
The AT89C51 is a low-power, high-performance CMOS 8-bit microcomputer with 4K
bytes of Flash Programmable and Erasable Read Only Memory (PEROM). The
device is manufactured using Atmel’s high density nonvolatile memory technology
and is compatible with the industry standard MCS-51™ instruction set and pinout. The
on-chip Flash allows the program memory to be reprogrammed in-system or by a con-
ventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with
Flash on a monolithic chip, the Atmel AT89C51 is a powerful microcomputer which
provides a highly flexible and cost effective solution to many embedded control appli-
cations.
(continued)
Pin Configurations
PDIP
PQFP/TQFP
INDEX
CORNER
P1.5
P1.6
P1.7
RST
(RXD) P3.0
NC
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
4
44
34
2
4
14
03
93
83
73
6
3
53
4
1 33
2 32
3 31
4 30
5 29
6 28
7 27
8 26
9 25
10 24
11 23
1
21
31
41
51
61
71
1
8
9
2
02
12
2
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA/VPP
NC
ALE/PROG
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
RST
(RXD) P3.0
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
(WR) P3.6
(RD) P3.7
X TA L 2
X TA L 1
GND
1 40
2 39
3 38
4 37
5 36
6 35
7 34
8 33
9 32
10 31
11 30
12 29
13 28
14 27
15 26
16 25
17 24
18 23
19 22
20 21
PLCC
VCC
P0.0 (AD0)
P0.1 (AD1)
P0.2 (AD2)
P0.3 (AD3)
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA/VPP
ALE/PROG
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
P2.4 (A12)
P2.3 (A11)
P2.2 (A10)
P2.1 (A9)
P2.0 (A8)
INDEX
CORNER
P1.5
P1.6
P1.7
RST
(RXD) P3.0
NC
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
6 4 2 44 42 40
7 5 3 1 43 4139
8 38
9 37
10 36
11 35
12 34
13 33
14 32
15 31
16 30
11781 92 02 12 22 32 42 52 62 72289
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA/VPP
NC
ALE/PROG
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
8-Bit
Microcontroller
with 4K Bytes
Flash
AT89C51
0265F-A–12/97
4-29
1 page  
AT89C51
Power Down Mode
In the power down mode the oscillator is stopped, and the
instruction that invokes power down is the last instruction
executed. The on-chip RAM and Special Function Regis-
ters retain their values until the power down mode is termi-
nated. The only exit from power down is a hardware reset.
Reset redefines the SFRs but does not change the on-chip
RAM. The reset should not be activated before VCC is
restored to its normal operating level and must be held
active long enough to allow the oscillator to restart and sta-
bilize.
Lock Bit Protection Modes
Program Memory Lock Bits
On the chip are three lock bits which can be left unpro-
grammed (U) or can be programmed (P) to obtain the addi-
tional features listed in the table below:
When lock bit 1 is programmed, the logic level at the EA pin
is sampled and latched during reset. If the device is pow-
ered up without a reset, the latch initializes to a random
value, and holds that value until reset is activated. It is nec-
essary that the latched value of EA be in agreement with
the current logic level at that pin in order for the device to
function properly.
Program Lock Bits
LB1 LB2 LB3
1 UUU
2 PUU
3 PPU
4PPP
Protection Type
No program lock features.
MOVC instructions executed from external program memory are disabled from fetching code
bytes from internal memory, EA is sampled and latched on reset, and further programming of the
Flash is disabled.
Same as mode 2, also verify is disabled.
Same as mode 3, also external execution is disabled.
Programming the Flash
The AT89C51 is normally shipped with the on-chip Flash
memory array in the erased state (that is, contents = FFH)
and ready to be programmed. The programming interface
accepts either a high-voltage (12-volt) or a low-voltage
(VCC) program enable signal. The low voltage program-
ming mode provides a convenient way to program the
AT89C51 inside the user’s system, while the high-voltage
programming mode is compatible with conventional third
party Flash or EPROM programmers.
The AT89C51 is shipped with either the high-voltage or
low-voltage programming mode enabled. The respective
top-side marking and device signature codes are listed in
the following table.
Top-Side Mark
VPP = 12V
AT89C51
xxxx
yyww
VPP = 5V
AT89C51
xxxx-5
yyww
Signature
(030H)=1EH
(031H)=51H
(032H)=FFH
(030H)=1EH
(031H)=51H
(032H)=05H
The AT89C51 code memory array is programmed byte-by-
byte in either programming mode. To program any non-
blank byte in the on-chip Flash Memory, the entire memory
must be erased using the Chip Erase Mode.
Programming Algorithm: Before programming the
AT89C51, the address, data and control signals should be
set up according to the Flash programming mode table and
Figures 3 and 4. To program the AT89C51, take the follow-
ing steps.
1. Input the desired memory location on the address
lines.
2. Input the appropriate data byte on the data lines.
3. Activate the correct combination of control signals.
4. Raise EA/VPP to 12V for the high-voltage programming
mode.
5. Pulse ALE/PROG once to program a byte in the Flash
array or the lock bits. The byte-write cycle is self-timed
and typically takes no more than 1.5 ms. Repeat steps
1 through 5, changing the address and data for the
entire array or until the end of the object file is reached.
Data Polling: The AT89C51 features Data Polling to indi-
cate the end of a write cycle. During a write cycle, an
attempted read of the last byte written will result in the com-
plement of the written datum on PO.7. Once the write cycle
has been completed, true data are valid on all outputs, and
the next cycle may begin. Data Polling may begin any time
after a write cycle has been initiated.
Ready/Busy: The progress of byte programming can also
be monitored by the RDY/BSY output signal. P3.4 is pulled
low after ALE goes high during programming to indicate
BUSY. P3.4 is pulled high again when programming is
done to indicate READY.
4-33
5 Page 
AT89C51
External Program Memory Read Cycle
ALE
PSEN
PORT 0
PORT 2
tLHLL
tAVLL
tLLPL
tLLAX
A0 - A7
tPLAZ
tLLIV
tPLIV
tPXIZ
tPXIX
INSTR IN
tPLPH
tPXAV
tAVIV
A8 - A15
A0 - A7
A8 - A15
External Data Memory Read Cycle
ALE
tLHLL
PSEN
RD
PORT 0
PORT 2
tAVLL
tLLDV
tLLWL
tLLAX
tRLAZ
tRLRH
tRLDV
A0 - A7 FROM RI OR DPL
DATA IN
tAVWL
tAVDV
P2.0 - P2.7 OR A8 - A15 FROM DPH
tWHLH
tRHDZ
tRHDX
A0 - A7 FROM PCL
INSTR IN
A8 - A15 FROM PCH
4-39
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet AT89C51.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AT89C51 | 8-Bit Microcontroller with 4K Bytes Flash | ATMEL Corporation |
| AT89C5115 | Low Pin Countl 8-bit Microcontroller | ATMEL Corporation |
| AT89C5121 | 8-bit Microcontroller | ATMEL Corporation |
| AT89C5122 | Smart Card Reader ICs | ATMEL Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |